7742130_003 CYLINDER BLOCK Volvo.Penta
D100BHC; D100BRC; TD100AHC
CYLINDER
Price: query
Rating:
Compatible models:
D100BHC; D100BRC; TD100AHC
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
Table 1
Required Tools
Part Number Part Name Quantity
1U-5470
or
198-4240 Engine Pressure Group
or
Digital Pressure Indicator 1
Illustration 1 g00295554
1U-5470 Engine Pressure Group
Air Inlet Restriction
There will be a reduction in the performance of the engine if there is a restriction in the air inlet system.
Illustration 2 g02148248
Right side view of the engine
(1) Air filter restriction indicator
(2) Air cleaner cover assembly
In order to check for a plugged air filter, observe air filter restriction indicator (1). Refer to Illustration 2. Replace the filter if the air filter restriction indicator indicates that the restriction pressure is above the specified limit. Refer to the Operation and Maintenance Manual.
Illustration 3 g02148273
Illustration 4 g02148337
(3) Hoses
(4) Air cleaner cover assembly
(5) Tube
(6) Turbocharger
Inspect the engine air cleaner inlet, tubes (5), and hoses (3) in order to ensure that the passageway is not blocked or collapsed. Refer to Illustration 3 and Illustration 4.
Check for dirt contamination on the clean side of the engine air cleaner element. If any dirt contamination is observed, contaminants are flowing past the engine air cleaner element and/or the seal for the engine air cleaner element.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Use the differential pressure gauge of the 1U-5470 Engine Pressure Group.
Connect the vacuum port of the differential pressure gauge to the test location. The test location may be located anywhere along the air inlet piping after the air cleaner but before the turbocharger.
Leave the pressure port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4.d by 1.8.
Compare the result from Step 4.e to the appropriate values that follow. The air flow through a used engine air cleaner may have a restriction. The air flow through a plugged engine air cleaner will be restricted to some magnitude. In either case, the restriction must not be more than the following amount: Maximum restriction ... 7.6 kPa (30.54 inch of H2O)The air flow through a new engine air cleaner element must not have a restriction of more than the following amount: Maximum restriction ... 3.7 kPa (14.87 inch of H2O)Exhaust Restriction
There will be a reduction in the performance of the engine if there is a restriction in the exhaust system.Note: Excessive idling can cause the muffler, the catalytic converter/muffler. A plugged muffler, a plugged catalytic converter/muffler can lead to an increase in exhaust back pressure. Operating the engine in cold conditions may cause the muffler, the catalytic converter/muffler to plug. One indication of a plugged muffler, catalytic converter is poor engine response.Back pressure is the difference in the pressure between the exhaust at the outlet elbow and the atmospheric air.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Making contact with a running engine can cause burns from hot parts and can cause injury from rotating parts.When working on an engine that is running, avoid contact with hot parts and rotating parts.
Connect the pressure port of the differential pressure gauge to the test location. The test location can be located anywhere along the exhaust piping after the turbocharger but before the muffler.
Leave the vacuum port of the differential pressure gauge open to the atmosphere.
Start the engine. Run the engine in the no-load condition at high idle.
Record the value.
Multiply the value from Step 4 by 1.8.
Compare the result from Step 5 to the value that follows. Back pressure from the exhaust must not be more than the following amount: Maximum back pressure ... 6.8 kPa (27.33 inch of H2O)
Parts cylinder Volvo Penta:
1545210
1545210 Cylinder block
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK, TMD100C
275038
275038 Cylinder liner kit
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK
275036
275036 Cylinder liner kit
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK
3803037
275551
275551 Cylinder head gasket
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, MD100A; TMD100A; TMD100AK
3803038
7742130_001
7742130_002