828813 Volvo.Penta Cable block

Illustration 1 g00287638
Right Side View (1) Cylinder head studsInstall the cylinder head studs with the following procedure:
Coat the lower half of each stud with 1.5 mm (.06 inch) thick coating of 4C-4774 Water and Temperature Resistant Grease .
Thoroughly clean the top of the cylinder block.
Install the cylinder head studs.Tighten the cylinder head studs to the following torque. ... 100 20 N m (75 15 lb ft)
Apply a bead of sealant at the top of the block around each stud. The sealant will ensure that the counterbore is filled with grease.
Coat the upper half of each stud with 1.5 mm (.06 inch) thick coating of 4C-4774 Water and Temperature Resistant Grease . (2) The dowels protrude from the front face of the cylinder block at the following distance. ... 8.0 1.0 mm (.32 .04 inch) (3) The dowels protrude from the rear face of the cylinder block at the following distance. ... 20.0 1.0 mm (.79 .04 inch) (4) The dowels protrude from the front face of the cylinder block at the following distance. ... 55.0 1.0 mm (2.17 .04 inch)
Illustration 2 g00287639
Front View Of Cylinder Block (5) The dowels protrude above the cylinder block face at the following distance. ... 8.0 1.0 mm (.32 .04 inch) (6) The dowels protrude above the cylinder block face at the following distance. ... 60.0 1.0 mm (2.36 .04 inch) (7) Bore in the block for main bearings ... 265.000 0.020 mm (10.4330 .0008 inch)1.00 mm (.040 inch) oversize ... 266.000 0.020 mm (10.4724 .0008 inch)2.00 mm (.080 inch) oversize ... 267.000 0.020 mm (10.5118 .0008 inch) (8) The center line of the crankshaft bearing bore to the top surface of the cylinder block ... 946.00 mm (37.244 inch) (9) Procedure for tightening the main bearings
Torque the studs in the cylinder block.Torque for the studs ... 100 20 N m (75 15 lb ft)
Assemble the main bearing cap and the washer. Hand tighten the nut.
Tighten all side bolts by hand. Ensure that the washer face and the side bolt threads have a clean coating of 4C-5593 Anti-Seize Compound . Ensure that all surfaces that contact the bearing are free of 4C-5593 Anti-Seize Compound .
Start at the front face of the block.Tighten the side bolts on the side of the cap with the tab slot to the following torque. ... 215 40 N m (160 30 lb ft)
Simultaneously tension each pair of the studs with either of the following tensioners: 207-5034 Stud Tensioner Tool Gp ... 65000 2400 kPa (9425 350 psi) 191-5320 Stud Tensioner Tool Gp ... 111500 3950 kPa (16170 570 psi)Tighten the nuts by hand. Slowly release the pressure.
Repeat Step 5. (10) Tighten the side bolts according to the following procedure.
Start at the front face of the block.Tighten the side bolts on the side of the cap opposite the tab slot to the following torque. ... 215 40 N m (160 30 lb ft)
Start at the front face of the block.Tighten the side bolts on the side of the cap with the tab slot to the following torque. ... 1825 175 N m (1340 130 lb ft)
Start at the front face of the block.Tighten the side bolts on the side of the cap opposite the tab slot to the following torque. ... 1825 175 N m (1340 130 lb ft) (11) Width of main bearing cap ... 499.95 0.03 mm (19.683 .001 inch)Width of cylinder block for main bearing cap ... 500.00 0.05 mm (19.685 .002 inch)Clearance between the sides of the main bearing cap and the cylinder block ... 0.03 to 0.13 mm (.001 to .005 inch)
Illustration 3 g00287640
Main Bearing Cap (12) The dowel protrudes from the main bearing cap at the following distance. ... 10.0 0.5 mm (.39 .02 inch) (13) Main bearing cap