22414661 Volvo.Penta Camshaft

Table 1
Lamp Outputs (Typical Application)    
Lamp    Required
or
Optional    Programming Options    
Default Output Terminal Alternative
Output Terminal Programmable to a J1939 Device    
Diesel Particulate Filter Regeneration Disabled     Required     J1/P1:13     High Side Drivers
J1/P1:10, 11, 12, 13, 19, 20, 21
Low Side Drivers
J1/P1:28, 29, 30, 31
J1939 - Body Controller
J1939 - Cab Controller
J1939 - Instrument Cluster
J1939 - Cab Display     N/A    
PMS Warning Lamp     J1/P1:29
Diesel Particulate Filter     J1/P1:30
High Exhaust System Temperature     J1/P1:31
Check Engine Lamp     J1/P1:28
Red Stop Lamp     Optional     None    
Low Oil Pressure    
High Coolant Temperature    
Low Coolant Level    
Fast Idle    
PTO Switch On    
ARD Disable Lamp    
Illustration 1 g02154248
Illustration 2 g02476892
P1 terminals for the J1939 data linkTesting the CircuitsThe ECM briefly activates the following lamps when the keyswitch is turned from OFF to ON:
"Amber Warning Lamp"
"Red Stop Lamp"
"DPF Lamp"
"High Exhaust System Temperature Lamp"
"Aftertreatment Disable Lamp" (if equipped)Special tests on the Cat ET can activate every lamp except the check engine lamp. The special tests activate the lamps for all programming options.
Table 2
Troubleshooting Test Steps    Values    Results    
1. Test the Circuit
If the problem is related to one of the following lamps, turn the keyswitch from OFF to ON in order to test the circuit.
"Amber Warning Lamp"
"Red Stop Lamp"
"DPF Lamp"
"High Exhaust System Temperature Lamp"
"Aftertreatment Disable Lamp" (if equipped)
Otherwise, use the appropriate special test on Cat ET to test the circuit.
Watch the lamp during the test.
   
Circuit test    
Result: Yes - The lamp does not illuminate.
Troubleshoot any active codes before continuing with this procedure.
Proceed to Test Step 2.
Result: No - The lamp illuminates.
There is a problem with the wiring if the problem is intermittent. Troubleshoot the wiring by referring to the electrical schematic.
STOP
   
2. Check the Bulb
Replace the bulb with a bulb that is known to be good. Test the circuit again.
   
Bulb    
Result: Yes - The lamp illuminates. The problem is resolved.
STOP
Result: No - The lamp does not illuminate. The bulb is OK.
The +Battery or the ground is not present at the lamp. Refer to the electrical schematic.
Troubleshoot the wiring by referring to the electrical schematic if the lamp output is programmed to a J1939 device.
Proceed to Test Step 3 if the lamp output is programmed to a J1/P1 terminal..
   
3. Troubleshoot the Wiring for the Lamp
Check the wiring for an open circuit. Pay particular attention to possible problems with electrical connectors.
   
Lamp wiring    
Result: Yes - There is an open circuit in the wiring for the lamp.
Make the necessary repairs.
STOP
Result: No - The wiring for the lamp is OK.
Proceed to Test Step 4.
   
4. Test the ECM Output
A. Verify that the P1 connector is connected to the ECM.
B. Use Cat ET to determine the programming option for the lamp output. Then, refer to Illustration 1 in order to determine if the ECM output terminal is a high side ECM driver or a low side ECM driver.
C. Perform the following procedure if the P1 terminal is a high side driver:
Use 7X-1710 Multimeter Probes to connect a test lamp between the P1 terminal for the lamp and terminal P1-63 (−Battery).
D. Perform the following procedure if the P1 terminal is a low side driver:
Use 7X-1710 Multimeter Probes to connect a test lamp between the P1 terminal for the lamp and terminal P1-53 (Unswitched +Battery).
E. Turn the keyswitch to the ON to test the circuit. Watch the test lamp while the output is activated.
   
ECM output    
Result: Yes - The test lamp illuminates. However, the indicator lamp does not illuminate.
Identify the cause of the wiring problem. Make the necessary repairs.
STOP
Result: No - The test lamp does not illuminate. There is a problem with the ECM.
Replace the ECM.
STOP
    Contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).