243229 Volvo.Penta Carbon brush set


243229 Carbon brush set Volvo.Penta AQ115A; AQ115B; AQ130 Carbon
243229 Carbon brush set Volvo Penta
Rating:
93

Buy Carbon brush set 243229 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$47.23
 

31-01-2022

-: -
243229: SPACER FOR LINDE
LINDE || All Brand new & rebuilt items comes with 1 year warranty. || SPACER FOR LINDE. CATEGORY FORKLIFT PARTS. THIS PART IS ALSO LISTED UNDER THE FOLLOWING PART NUMBERS: 243229 W243229 LI W243229 LINDE W243229 LINDEW243229. COMES WITH 1 YEAR LIMITED WARRANTY.
$122.70
 

31-08-2017

Carrera: Carrera
CARRERA - CARRERA 4 243229 TZG 58 mm
Purple / Purple Color||Aviator Style||UVA/UVB Protection||58mm / 12mm / 140mm
$1,189.70
 

31-01-2022
88.0[39.60] Pounds
-: -
Onki 243229 Brush Guard
243229
Number on catalog scheme: 26
 

Compatible models:

Volvo Penta entire parts catalog list:

AQ115A; AQ115B; AQ130; AQ130A; AQ130B; AQ130C; AQ130D; AQ165A; AQ170A; AQ170B; AQ170C; AQD21A; BB115A; BB115B; BB115C; BB165A; BB170A; BB170B; BB1

Information:


Table 1
Specifications for 332-7941 Spring and 326-7290 Spring    
Callout     Part Number     Part Name     Specification Description    
10     332-7941     Spring     The load for the inlet valve spring is
209 to 231 N (47 to 52 lb).
The length of the inlet valve spring is
31.5 mm (1.2402 inch).
The load for the inlet valve spring is
389.5 to 430.5 N (87.5 to 97 lb).
The length of the inlet valve spring is
22.2 mm (0.87401 inch).    
10     326-7290     Spring     The load for the exhaust valve spring is
161.5 to 178.5 N (36.3 to 40.1 lb).
The length of the exhaust valve spring is
31.5 mm (1.2402 inch).
The load for the exhaust valve spring is
337.9 to 373.5 N (76 to 84 lb).
The length of the exhaust valve spring is
21.5 mm (0.8465 inch).    Removal Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
A     9U-6195     Valve Spring Compressor     1    
268-1969 Adapter     1    
276-1221 Head     1    
B (1)     9U-6198     Crankshaft Turning Tool     1    
B (2)     5P-7306     Housing     1    
5P-7305 Engine Turning Tool     1    
( 1 ) The Crankshaft Turning Tool is used on the front pulley.
( 2 ) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod" for the correct procedure.Note: Either Tooling (B) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure should be adopted in order to remove the valve springs when the cylinder head is installed to the engine. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves" for the procedure to remove the valve springs from a cylinder head that has been removed from the engine.Note: Ensure that the appropriate piston is at top dead center before the valve spring is removed. Failure to ensure that the piston is at top dead center may allow the valve to drop into the cylinder bore.
Personal injury can result from being struck by parts propelled by a released spring force.Make sure to wear all necessary protective equipment.Follow the recommended procedure and use all recommended tooling to release the spring force.
Plug the apertures for the push rods in the cylinder head in order to prevent the entry of loose parts into the engine.
Illustration 1 g01978813
Follow Step 1.a through Step 1.h in order to remove the harness assemblies for the electronic unit injectors.
Place a temporary identification mark on connections (1) for harness assembly (3) for electronic unit injectors (2) .
Use a deep socket to remove connections (1) from electronic unit injectors (2) .
Cut cable straps (4) and remove the remaining sections of the cable straps from the cylinder head.
Disconnect plug (6) from harness assembly (3) .
Remove bolt (5) from harness assembly (3) .
Withdraw harness assembly (3) from the cylinder head.
Remove O-ring seal (7) from harness assembly (3) .
Repeat Step 1.a through Step 1.g in order to remove the remaining harness assemblies.
Illustration 2 g02501157
Ensure that the valve spring is compressed squarely or damage to the valve stem may occur.
Follow Step 2.a through Step 2.d in order to position the appropriate piston at top dead center.
Install Tooling (A) in position on the cylinder head in order to compress a valve spring (10) for the appropriate piston.
Use Tooling (A) in order to compress valve spring (10) and open the valve slightly.Note: Do not compress the spring so that valve spri


Parts carbon Volvo Penta:

834853
Carbon brush set
834853 Carbon brush set
AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, MD40A; TMD40A; TMD40B
844014
 
844014 Carbon brush set
251A, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A, AQ200D; AQ200F; 280B, AQ205A; AQ2
825527
 
825527 Carbon retainer
AQ115A; AQ115B; AQ130, D42A; D42A PP, MD1B; MD2B; AQD2B, MD21B; AQD21B, TD30A; TD31ACE; TD40A
829706
 
829706 Carbon brush set
AQ115A; AQ115B; AQ130, MD21B; AQD21B
829016
Carbon brush set
829016 Carbon brush set
AQ115A; AQ115B; AQ130, MD21B; AQD21B
240130
Carbon brush set
240130 Carbon brush set
AQ115A; AQ115B; AQ130
273500
 
273500 Carbon brush set
AQ115A; AQ115B; AQ130
Back to top