3850712 Volvo.Penta Carburettor


3850712 Carburettor Volvo.Penta 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA Carburettor
3850712 Carburettor Volvo Penta
Rating:
53

Buy Carburettor 3850712 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$207.98
 

16-06-2021

-: -
Dinosaur Electronics Rpl.board for Dometic 3850712. 3850712replboard
$194.00
 

02-02-2024
0.0006[0.00] pounds
US: RV Wholesale Direct
Dinosaur Electronics RV Motorhome Trailer Replacement for Domectic 3850712.01 with Built-in Ignitor, Fuse Protected
Dinosaur Electronics Dometic replacement 3850712. 01
$240.47
 

16-09-2024
0.0006[0.00] Pounds
US: Autoplicity ✅
Dinosaur Electronics 3850712REPLBOARD Rpl.board For Dometic 3850712.
Dinosaur Electronics New
Number on catalog scheme: 1
 

Volvo Penta entire parts catalog list:

5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE; 5.0FIPHURCE; 5.0FIPHUSCE; 5.0FLPHUB; 5.0FLPHUC; 5.0FLPHUE; 5.0FLPHUR; 5.0FLPHUS; 5.8FIIHUBCE; 5.8FII
5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE; 5.0FIPNCSCE; 5.0FLPNCA; 5.0FLPNCB; 5.0FLPNCM; 5.0FLPNCS
5.0FLPMDA; 5.8FLPMDA

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     1P-0510     Driver Gp     1    
C     248-3311     Holding Fixture     1    
D     248-3310     Spanner Wrench     1    
E     8H-0663     Bearing Puller Gp     1    
F     1U-6396     O-Ring Assembly Compound     -    
G     7N-8268     Installation Tool     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01040290
Use Tooling (E) and a suitable press to install bearing assembly (17) on pump shaft (12) .
Install bearing cone (23) on the pump shaft.
Install spacer (22) and bearing cups (21) on the pump shaft.
Install bearing cone (20) on the pump shaft.
Illustration 2 g01035607
The splined end of the pump shaft is marked in order to indicate either RH threads or LH threads on the pump shaft. Install bearing locknut (16). Use Tooling (D) on the bearing locknut. Tighten the bearing locknut to a torque of 300 30 N m (221 22 lb ft).Note: The torque wrench must be 90 degrees to Tooling (D) .
Install set screws (15) and tighten to a torque of 4 1 N m (35 9 lb in).
Illustration 3 g01035690
Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Apply Tooling (F) to the outside diameter of ceramic seal (18). Use Tooling (G) and hand pressure to install ceramic seal (18) in bearing housing (3) .
Illustration 4 g01035699
Use Tooling (A) and a suitable press to install lip seal (19) in bearing housing (3). Ensure that the lip is toward the outside.Note: Install the lip seal dry. Install the lip seal within two minutes of removal from the shipping sleeve.
Illustration 5 g01035809
Lubricate pump shaft (12) with clean engine oil. Install the pump shaft in bearing housing (3). Install retainer (11). Install socket head bolts (10) and tighten to a torque of 12 3 N m (9 2 lb ft).
Illustration 6 g01035829
Note: Do not damage the wear surfaces of the carbon ring or the ceramic ring. Do not touch the wear surfaces of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal.
Remove spring (14) from ceramic seal (13) .
Apply Tooling (F) to the inside diameter of ceramic seal (13). Use hand pressure and the tool that is supplied with the water pump seal group to install the ceramic seal. The face of ceramic seal (13) should make light contact with ceramic seal (18) .
Install spring (14) .
Lubricate pump shaft (12) on bearing housing (3) with clean engine oil. Position impeller (9) on the pump shaft.
Illustration 7 g01035846
Place bearing housing (3) on impeller (9). Use a suitable press and press pump shaft (12) into the impeller. Install the impeller so the dimension between the impeller and the pump shaft is 0.000 0.076 mm (0.0000 0.0030 inch).
Illustration 8 g01035264
Install O-ring seal (8) on bearing housing (3). Lubricate the O-ring seal with clean engine oil.
Position bearing housing (3) in housing (5). Install washers and bolts (7) .


Parts carburettor Volvo Penta:

3854584
 
3854584 Carburettor, 290 DP
5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA
3854051
 
3854051 Carburettor
5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FLPMDA; 5.8FLPMDA, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE
Back to top