854030 Volvo.Penta Catch


854030 Catch Volvo.Penta 230A; 230B; 250A, AQ131A; AQ131B; AQ131C, AQ231A; AQ231B; AQ231LB Catch
854030 Catch Volvo Penta
Rating:
38

Buy Catch 854030 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$73.02
 

13-02-2024

US: KHC Shop
4 Inch Schedule 80 PVC Van Stone Flange - Slip (854-040)
JF World 3" Schedule 80 PVC Van Stone Flange - Slip (854-030)
$28.45
 

13-05-2024
1.75[0.79] Pounds
US: Agricultural Service
GF Piping Systems PVC Pipe Fitting, Van-Stone Flange, Schedule 80, Gray, 3" Slip Socket
GF Piping Systems Van Stone flange for joining two pipes or connecting valves in a piping system || Socket opening for connecting to a male pipe or fitting || PVC for chemical and corrosion resistance, high strength, and less weight than fittings made from metal || Operating temperature range of 0 to 60 degrees C (32 to 140 degrees F) || Meets ASTM D1784 and D1785 standards for quality assurance, and meets NSF standards 14 and 61 for potable water service
 

07-10-2017
1.71[0.45] pounds
Nibco: Nibco
Nibco 854-030 4551-A PVC Van Stone Flange, Socket, Solid, 3" Pipe Size
Van Stone two-piece design with webbed ring and separate rotating hub||Design stress of 2,000 psi at 73°F||Maximum service temperature 140°F||Universal Part No. 854
Number on catalog scheme: 40
 

Volvo Penta entire parts catalog list:

230A; 230B; 250A; 250B
AQ131A; AQ131B; AQ131C; AQ131D
AQ231A; AQ231B; AQ231LB; 290A; DP-A; SP-A; 275A; 285A

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     6V-6146     Load Leveler     1    Start By:
Remove the cab. Refer to Disassembly and Assembly, RENR5140, "Cab - Remove".
Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler, Fan, and Gear Motor - Remove".
Remove the crankcase guard. Refer to Disassembly and Assembly, "Crankcase Guard - Remove".
Personal injury or death can result from improper lifting or blocking.When a hoist or jack is used to lift any part or component, stand clear of the area. Be sure the hoist or jack has the correct capacity to lift a component. Install blocks or stands before performance of any work under a heavy component.Approximate weights of the components are shown. Clean all surfaces where parts are to be installed.
At operating temperature, the hydraulic tank is hot and under pressure.Hot oil and components can cause personal injury. Do not allow hot oil or components to contact skin.Remove the filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. Remove the filler cap slowly in order to relieve pressure.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Put Identification marks on all hoses, all lines, all tubes and all wires for installation purposes. Plug all hoses, all lines and all tubes. This helps prevent fluid loss and this will help keep contaminants from entering the system.
Refer to the Operation and Maintenance Manual in order to drain the fluids from the following items:
The engine
The cooling system
The transmission
Illustration 1 g00806426
Illustration 2 g00806427
Right side of the Transmission
Remove four clips (1) that secure harness (2) to the machine frame and to the brackets on the top side of the transmission. Disconnect electrical connector (3) for the transmission temperature sender from harness (2). Feed the harness toward the front of the machine.Note: Harness (2) must be removed with the engine. Make sure that the harness is coiled and secured to the engine. Do not secure the harness in a position that will catch on removal of the engine.
Illustration 3 g00806428
Remove four bolts (4), the washers and two half clamps (5) in order to disconnect hose (6) from tube (7). Remove two bolts (8), the nut, the washers and the clamps that secure tube (7) to the engine.
Illustration 4 g00806429
Remove bolt (9), the washers and the nut in order to remove two clamps (10) that secure tube (7) to the transmission filler tube. Remove bolt (11), the washers and the nut in order to remove two clamps (12) that secure the hose bundle to tube (7). Remove four bolts (13), the washers and two half clamps (14) and disconnect tube (7) from oil cooler (15). Remove tube (7) from the machine.
Illustration 5 g00806784
Remove four bolts (16), the washers and two half clamps (17) in order to disconnect hose (18) from oil cooler (15) for the brakes. Move the hose aside.


Parts catch Volvo Penta:

897873
 
897873 Catch
AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B
814391
 
814391 Catch
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A
854035
Catch
854035 Catch
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AQ131A; AQ131B; AQ131C, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ231A; AQ231B; AQ231LB, AQ271A; AQ271B; AQ271C, AQ311A; AQ311B, MD31A;
Back to top