835545 Volvo.Penta Chain gear


835545 Chain gear Volvo.Penta AQ175A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A Chain
835545 Chain gear Volvo Penta
Rating:
63

Buy Chain gear 835545 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$12.46
 

31-03-2024

Amazon.com
Tradespro 835545 SAE Ratcheting Box Wrench Set, 3-Piece
Tradespro Product Type :Tools || Package Dimensions :1.75" L X5.25" W X14.5" H || Country Of Origin :China || Package Weight :1.15Lbs
Number on catalog scheme: 4
 

Information:

Starting Motor
Illustration 1 g01964824
Typical example
12 V 4 kW Starting Motor
(1) Terminal 30 for connection of the battery cable
(2) Terminal 50 for connection of ignition switch
(3) Terminal 31 for connection of the ground
Illustration 2 g01964833
Typical example
24 V 5.5 kW Starting Motor
(4) Terminal 30 for connection of the battery cable
(5) Integrated Magnetic Switch (IMS)
(6) Terminal 50 for connection of ignition switch
(7) Terminal 31 for connection of the ground The starting motor turns the engine via a gear on the engine flywheel. The starting motor speed must be high enough in order to initiate a sustained operation of the fuel ignition in the cylinders.The starting motor consists of the main armature and a solenoid. The solenoid is a relay with two windings Pull-In (PI) and Hold-In (HI). Upon activation of ignition switch, both windings move the iron core by electromagnets. The linkage from the iron core acts to move the pinion toward the flywheel ring gear for engagement. Upon complete engagement, the solenoid completes the high current circuit that supplies electric power to the main armature in order to provide rotation. During cranking of the engine, only the Hold-In (HI) winding is active.The ignition switch is deactivated once the desired engine speed has been achieved. The circuit is disconnected. The armature will stop rotating. Return springs that are located on the shafts and the solenoid will disengage the pinion from flywheel ring gear back to the rest position.The armature of the starting motor and the mechanical transmissions may be damaged if the increases in the speed of the engine are greater than the pinion of the starting motor. Damage may occur when the engine is started or after the engine is started. An overrunning clutch prevents damage to the armature of the starting motor and mechanical transmissions.Certain higher powered starting motors are designed with an Integrated Magnetic Switch (IMS). The Integrated Magnetic Switch (IMS) is activated by the ignition switch. The solenoid circuit then engages the starting motor. The benefit of Integrated Magnetic Switch (IMS) is a lower current in the ignition circuit that will allow the engine ECM to control ignition without the use of a relay.Alternator
The electrical outputs of the alternator have the following characteristics:
Three-phase
Full-wave
RectifiedThe alternator is an electro-mechanical component. The alternator is driven by a belt from the crankshaft pulley. The alternator charges the storage battery during the engine operation.The alternator is cooled by an external fan which is mounted behind the pulley. The fan may be mounted internally. The fan forces air through the holes in the front of the alternator. The air exits through the holes in the back of the alternator.The alternator converts the mechanical energy and the magnetic field into alternating current and voltage. This conversion is done by rotating a direct current electromagnetic field on the inside of a three-phase stator. The electromagnetic field is generated by electrical current flowing through a rotor. The stator generates alternating current and voltage.The alternating current is changed to direct current by a three-phase, full-wave rectifier. Direct current flows to the output terminal of the alternator. The direct current is used for the charging process.A regulator is installed on the rear end of the alternator. Two brushes conduct current through two slip rings. The current then flows to the rotor field. A capacitor protects the rectifier from high voltages.The alternator is connected to the battery for charging and machine load requirements. A warning lamp can be connected via the ignition switch. This wiring is optional.


Parts chain Volvo Penta:

841851
855906
 
855906 Chain gear
AQ175A, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F
835405
 
835405 Chain
AQ175A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ290A, AQ311A; AQ311B
835544
 
835544 Chain gear
AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A
835403
Chain gear
835403 Chain gear
AQ200B; AQ225B, AQ200C; AQ200D; AQ225C
855905
 
855905 Chain gear
AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ290A, AQ311A; AQ311B
Back to top