3886206 Volvo.Penta Charge air pipe


3886206 Charge air pipe Volvo.Penta D3-110I-A; D3-110I-B; D3-110I-C Charge
3886206 Charge air pipe Volvo Penta
Rating:
68

Buy Charge air pipe 3886206 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Volvo Penta entire parts catalog list:

D3-110I-A; D3-110I-B; D3-110I-C; D3-130A-A; D3-130I-A; D3-130A-B; D3-130I-B; D3-130A-C; D3-130I-C; D3-160A-A; D3-160I-A; D3-160A-B; D3-160I-

Information:


Illustration 1 g00553792
Crankshaft for 3408 Engine (1) Maximum length of pin out of crankshaft face ... 6.4 mm (0.25 inch) (2) Thrust plates at center main bearing (3) End play for the new crankshaft ... 0.13 to 0.50 mm (0.005 to 0.020 inch) (4) Minimum torque for five plugs ... 23 N m (17 lb ft)Make a hole with a punch on the crankshaft in order to hold the plug tightly. (5) Length of dowel out of the crankshaft ... 4.1 0.5 mm (0.16 0.02 inch) (6) Rear sealIf the seal and the sleeve have been separated, the rear seal cannot be used. Install the rear seal in the flywheel housing. The seal position is shown in the illustration. See Special Instruction SMHS8508.Refer to the following procedure to check installation.Distance from rear face of crankshaft to sleeve (Dimension A) ... 1.5 0.5 mm (0.06 0.02 inch)Distance from edge of sleeve to seal (Dimension B) ... 6.1 0.6 mm (0.240 0.024 inch)Note: The same procedure will be used with a crankshaft that has a crankshaft rear gear. (7) Maximum permissible temperature of the gear for installation on the crankshaft ... 232 °C (450 °F)Note: Install gear with V mark to the outside. (8) Refer to Connecting Rod Bearings. (9) Refer to Main Bearings. (10) Front sealIf the seal and the sleeve have been separated, the front seal cannot be used. Install the front seal in the front accessory drive housing. The seal position is shown in the illustration. See Special Instruction, SMHS8508.Refer to the following procedure to check installation.The sleeve must be flush with the front face of the crankshaft within the following value. ... 0.13 mm ( 0.005 inch)Distance from edge of sleeve to seal (Dimension C) ... 4.9 0.6 mm (0.19 0.02 inch)
Illustration 2 g00270355
Crankshaft for 3412 Engine (1) Maximum length of pin out of crankshaft face ... 6.4 mm (0.25 inch) (2) Thrust plates at center main bearing (3) End play for new crankshaft ... 0.13 to 0.50 mm (0.005 to 0.020 inch) (4) Minimum torque for five plugs ... 23 N m (17 lb ft)Make a groove with a punch on the crankshaft in order to hold the plug tightly. (5) Length of dowel out of crankshaft ... 4.1 0.5 mm (0.16 0.02 inch) (6) Rear sealIf the seal and the sleeve have been separated, the rear seal cannot be used. Install the rear seal in the flywheel housing. The seal position is shown in the illustration. See Special Instruction SMHS8508.Refer to the following procedure to check installation.Distance from rear face of crankshaft to sleeve (Dimension A) ... 1.5 0.5 mm (0.06 0.02 inch)Distance from edge of sleeve to seal (Dimension B) ... 6.1 0.6 mm (0.24 0.02 inch)Note: The same procedure will be used with a crankshaft that has a crankshaft rear gear. (7) Maximum permissible temperature of the gear for installation on the crankshaft ... 232 °C (450 °F)Note: Install gear with "V" mark to the outside. (8) Refer to Connecting Rod Bearings. (9) Refer to Main Bearings. (10) Front sealRefer to the following procedure to check installation.If the seal and the sleeve have been separated, the front seal cannot be used. Install the front seal in the front accessory drive housing. The seal position is shown in the illustration. See Special Instruction, SMHS8508.The sleeve must be flush with the front face of the crankshaft within the following value. ... 0.13 mm (0.005 inch)Distance from edge of sleeve to seal (Dimension C) ... 4.9 0.6 mm (0.19 0.02 inch)


Parts charge Volvo Penta:

888513
 
888513 Charge air cooler
D3-110I-A; D3-110I-B; D3-110I-C
3819136
 
3819136 Charge air cooler
D3-110I-A; D3-110I-B; D3-110I-C
3812610
 
3812610 Charge air cooler
D3-110I-A; D3-110I-B; D3-110I-C
Back to top