888144 Charge air pipe Volvo.Penta
TAD940GE; TAD941GE
Charge
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
TAD940GE; TAD941GE
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
2. Remove two bolts (1) and disconnect tube (2) from oil pump.3. Remove bolts (3) that hold oil pump to cylinder block.4. Remove oil pump.Install Oil Pump
1. Put the oil pump (1) in position on the cylinder block and install bolts and locks that hold it to engine.2. Connect tube to oil pump.3. Install suction bell and tube on oil pump.end by:a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43 7 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
Before installation, lubricant must be in the oil pump and it must turn freely.
end by: a) install oil pump
1. Put the oil pump (1) in position on the cylinder block and install bolts and locks that hold it to engine.2. Connect tube to oil pump.3. Install suction bell and tube on oil pump.end by:a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.2. Install the bearings in oil pump body assembly with tooling (A) as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP (2P1785) in SPECIFICATIONS.4. Put clean engine on all of the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly. 6. Install gears and shafts (6) in the oil pump body assembly.7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43 7 N m).10. Install the bearing in the idler gear with tooling (B) until it is even with the outside surface of the gear.11. Install the idler gear.
Before installation, lubricant must be in the oil pump and it must turn freely.
end by: a) install oil pump
Parts charge Volvo Penta:
40005102
40005102 Charge air cooler
1372, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD1340VE; TAD1341VE; TAD1342VE, TAD13
865127
865127 Charge air hose
1372, D12D-A MG; D12D-E MG, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), TAD1030G; TD1010G; TWD1010G, TAD1030GE; TAD1031GE; TAD1032GE, TAD1030P, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170V
3827870
3827870 Charge air cooler
D12D-A MG; D12D-E MG, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1240GE; TAD1241GE; TAD1242GE, TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE
3839462
3839462 Charge air pipe
D9A2A; D9A2A MG; D9A2A D9A-MG, TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE
3839235
3836401
3839303