1655158 Volvo.Penta Clutch housing


1655158 Clutch housing Volvo.Penta TD100G; TD100G-85; TD100G-87 Clutch
1655158 Clutch housing Volvo Penta
Rating:
28

Buy Clutch housing 1655158 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

Volvo Penta entire parts catalog list:

TD100G; TD100G-85; TD100G-87; TD100GG; TD100GG-85; TD100GG-87; TD100GGP-87; TD100HP-87; TD100HPB-87; TD100GP; TD100GP-85; TD100GGP; TID100K;

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1 Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (A) to turn the flywheel in order to access the connecting rod cap that will be removed.
Illustration 1 g00913801Note: Inspect the connecting rod and connecting rod cap for the proper identification mark. The connecting rod and the connecting rod cap should have an etched number on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.
Remove bolts (1) and connecting rod cap (2) from the crankshaft.
Push the connecting rod away from the crankshaft. Remove the upper half of the connecting rod bearing.Note: Be careful not to damage the cylinder liner or the crankshaft journal.
Remove the lower half of the connecting rod bearing from connecting rod cap (2).Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B Loctite Moly 50 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Illustration 2 g00913801
Illustration 3 g03746219
Section view of connecting rod showing torque sequence. Chamfer (3) and dowel (4) can be used to reference orientation.
Install the upper half of the connecting rod bearing on the connecting rod . Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod. Coat the connecting rod bearing with clean engine oil. Position the connecting rod onto a journal of the crankshaft.
Install the lower half of the connecting rod bearing on connecting rod cap (2). Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod cap. Coat the connecting rod bearing with clean engine oil.Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod. Install the chamfered side of the connecting rod cap next to the thrust surface of the crankshaft.
Apply Tooling (B) to the threads, the shank, and the seat of bolts (1).
Place connecting rod cap (2) into position. Install bolts (1). Use the following procedure to tighten the bolts:
Tighten Bolt (A) and Bolt (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) again to a torque of 90 5 N m (65 4 lb ft).
Place an index mark on the bolts and the connecting rod cap. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the engine oil pump.


Parts clutch Volvo Penta:

845618
 
845618 Clutch flange
D100A; D100AK; D100B, MD100A; TMD100A; TMD100AK, TAD1030G; TD1010G; TWD1010G, TAD1030P, TD100CHC; TD100CRC; TD121CHC, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD100G; TD100G-85; TD100G-87, TD60D; TD60D-83; TD60DPP-83, TD610G; TW
845616
 
845616 Clutch half
D100A; D100AK; D100B, MD100A; TMD100A; TMD100AK, TAD1030G; TD1010G; TWD1010G, TAD1030P, TD100CHC; TD100CRC; TD121CHC, TD100G-87; TD1030ME; TWD1030ME, TD100G-87; TD1030VE; TAD1030V, TD100G; TD100G-85; TD100G-87, TD60D; TD60D-83; TD60DPP-83, TD610G; TW
842520
 
842520 Clutch
D100A; D100AK; D100B, D120A; D120AK; TD120A, TD100G; TD100G-85; TD100G-87, TD120C, TD120HP-86; TD121; TD121G, TD120HPP; TID120HPP, TID120FPP; TID120FG; TD120G, TID121FG
813696
 
813696 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
815466
 
815466 Clutch fork
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
815480
Clutch
815480 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
819468
 
819468 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
267171
 
267171 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
Back to top