382185 Volvo.Penta Clutch ring


382185 Clutch ring Volvo.Penta D100A; D100AK; D100B, D120A; D120AK; TD120A Clutch
382185 Clutch ring Volvo Penta
Rating:
68

Buy Clutch ring 382185 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$373.42
 

01-09-2017
22.00[9.90] pounds
American S: American Shifter
American Shifter 382185 Shifter Kit (PG 23" Trim Kit CHR Dual Shift GRY Boot Ringed Knob For D19B5, 1 Pack)
Application: Powerglide||Shifter Style: Push Button & Side Detent||Shifter Arm Size: 23in Single Bend||Shifter Arm Finish: Chrome||Knob: Standard
Number on catalog scheme: 8
 

Compatible models:

Volvo Penta entire parts catalog list:

D100A; D100AK; D100B; TD100A; TD100AG; TD100AK
D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 138-7576 Link Bracket 2
C 6V-4876 Lubricant 1
D 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02054993
If crankshaft gear (6) was removed, install the gear on crankshaft (4).
Check the clearance of the main bearings.
Illustration 2 g02054995Note: The upper halves of the main bearings have an oil hole in the center.
Install the upper halves of main bearings (8) in the cylinder block. Coat the bearings with clean engine oil.
Install the upper halves of connecting rod bearings (9) in the connecting rod assemblies. Coat the bearings with clean engine oil.
Illustration 3 g02054216Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach Tooling (B) and a suitable lifting device to crankshaft (4). For 3508 Engines, the weight of the crankshaft is approximately 400 kg (880 lb). For 3512 Engines, the weight of the crankshaft is approximately 590 kg (1300 lb). For 3516 Engines, the weight of the crankshaft is approximately 800 kg (1760 lb). Position the crankshaft in the cylinder block.
Ensure that the lower halves of the main bearings are in position in the main bearing caps. Coat the bearings with clean engine oil. Note: Main bearing caps (5) must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Illustration 4 g01049012
Coat the threads of the bolts for the main bearing caps with clean engine oil. Except for the center main bearing cap, place the main bearing caps into position. Install the bolts and washers. Tighten the bolts according to the sequence that is shown in Illustration 4. Arrow (X) points to the front of the engine. Tighten the bolts to a torque of 190 14 N m (140 10 lb ft). Then tighten the bolts for an additional 180 5 degrees (1/2 turn).
Illustration 5 g02055020
Place clean engine oil on thrust plates (3). Install thrust plates (3).
Install the center main bearing. Use the tightening procedure that is in Step 7.
Use Tooling (D) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Make sure that the upper halves of the bearings are in position on the connecting rods. Make sure that the lower halves of the bearings are in position on the connecting rod caps.
Check the clearance of the connecting rod bearings.
Position one connecting rod onto a journal of the crankshaft. Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod.
Illustration 6 g01049104
Illustration 7 g02055042
Place Tooling (C) on the bolt threads, shanks, and seats.
Place connecting rod cap (2) into position. Install the bolts. Use the following procedure to tighten the bolts:
Tighten Bolts (A) and (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolts (C) and (D) again to a torque of 90 5 N m (65 4 lb ft).
Tighten each bolt for an additional 90 5 degrees (1/4 turn). An impact wrench may be used.
After measuring the clearance of the connecting rod bearing, coat the bearings with clean engine oil. Use the same procedure to install the remaining connecting rod caps.
Each counterweight is numbered and must be installed in the same position as the corresponding number on the crankshaft mounting pad in order to prevent damage to the crankshaft.


Parts clutch Volvo Penta:

837791
 
837791 Clutch housing
AQD70D; TAMD70D; TAMD70E, D100A; D100AK; D100B, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70C; TMD70C; TAMD70C, TAMD60A; TAMD60B, TD120C, TD60A; TD60B; TD60B PP, TD70G; TD70G-83; TD70GPP, TID120FPP; TID120FG; TD120G
824411
 
824411 Clutch housing
D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B
837377
 
837377 Clutch housing
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD100CHC; TD100CRC; TD121CHC,
821366
 
821366 Clutch
D100A; D100AK; D100B, D100BHC; D100BRC; TD100AHC, D120A; D120AK; TD120A, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A, TD120AHC; TD120ARC; TAD120AHC, TD120C
846107
 
846107 Clutch
D100A; D100AK; D100B, D120A; D120AK; TD120A, TD120C, TID120FPP; TID120FG; TD120G
815466
 
815466 Clutch fork
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
815480
Clutch
815480 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
819468
 
819468 Clutch
D100A; D100AK; D100B, TD100G; TD100G-85; TD100G-87
Back to top