3854161 Volvo.Penta Coil

If a 261-11 diagnostic code is active, verify that the wiring is installed correctly to the engine speed/timing sensors.The ECM has the ability to calibrate the mechanical differences between the Top Center (TC) of the flywheel and the TC of the timing gear on the camshaft. A magnetic transducer signals the TC of the flywheel to the ECM when a notch on a counterweight passes by the transducer. The engine speed/timing sensor signals the TC of the timing gear to the ECM. Any offset between the TC of the flywheel and the TC of the timing gear is stored into the memory of the ECM.Note: A timing calibration will not increase the available engine power.Table 2 lists the special tools that are required in order to perform this procedure.
Table 2
Required Special Tools
Part Number Description
7X-1171 Transducer Adapter
6V-2197 Transducer
7X-1695 Cable As
170-3519 Harness (1)
(1) This item is not required if the engine harness has a connector for timing calibration.
Install the Transducer Adapter.
Remove the electrical power from the ECM.
Use the appropriate engine turning tool to put either the No. 1 piston or the No. 6 piston at top center. Refer to the Systems Operation/Testing and Adjusting.
Refer to Table 3. After the top center position has been located, rotate the crankshaft for the number of degrees that is applicable to your engine model. Be sure to rotate the crankshaft in the direction of rotation that is specified in the Table.
Table 3
Crankshaft Rotation
Engine Model Number of Degrees Direction of Rotation
C7 100 Normal Rotation
C-9 85 Normal Rotation
C-10 60 Opposite Normal Rotation
C11 75 Normal Rotation
C-12 60 Opposite Normal Rotation
C13 75 Normal Rotation
C-15 60 Opposite Normal Rotation
C15 60 Opposite Normal Rotation
C-16 60 Opposite Normal Rotation
C18 30 Opposite Normal Rotation
Refer to Table 4. Locate the engine's timing calibration port.
Table 4
Location of the Timing Calibration Port
Engine Model Crankshaft Counterweight Engine Location
C7 3 Left Side
C-9 3 Left Side
C-10 8 Right Side
C11 8 Left Side
C-12 8 Right Side
C13 8 Left Side
C-15 2 Left Side
C15 2 Left Side
C-16 2 Left Side
C18 2 Left Side
Remove the plug from the timing calibration port.
Thread the transducer adapter into the port. Continue to the next test step.
Install the Transducer.
If the crankshaft is not in the correct position when the transducer is installed, the transducer will be damaged when the engine is started.
Apply clean engine oil to a 2D-6392 O-Ring Seal. Install the O-ring seal on the end of the 6V-2197 Transducer.
Push the transducer through the transducer adapter until the transducer contacts the crankshaft counterweight.
Withdraw the transducer 1.0 mm (0.04 inch) and hand tighten the nut on the adapter sleeve in order to secure the transducer. Move the O-ring seal against the adapter. Continue to the next test step.
Connect the 7X-1695 Cable As.
If the engine harness is equipped with a connector for timing calibration, connect the 7X-1695 Cable As to the connector for timing calibration and to the transducer.
If the engine harness is not equipped with a connector for timing calibration, perform the following procedure: Disconnect the P2 connector from the ECM.Determine the number of terminals on the P2 connector.Refer to Table 5. Remove the sealing plugs from the appropriate terminals. Do not discard the sealing plugs. The sealing plugs may be reinstalled when the timing calibration is complete.
Table 5
P2 Locations for Connection of the 7X-1695 Cable As
Wire Color 70 pin Connector 120 pin Connector
White 22 26
Yellow 23 36 Install the WH(White) wire of the 170-3519 Harness into the appropriate location.Install the YL(Yellow) wire of the 170-3519 Harness into the appropriate location. Disregard the pin-outs on the label of the harness.Note: Ensure that each wire is installed into the correct location. The timing calibration will not be successful if the wires are installed incorrectly.Connect the J2/P2 connec