3853704 Volvo.Penta Connector, test input

Recommended Actions
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Determine if a code is present.
Codes
Result : A 4360-16 or E946 (2) code with an ETI of 1 or 2 is active or logged.
Proceed to Test Step 2.
Result : A 4360-17, E947 (1), 4360-18 or E947 (2) code is logged or active.
Proceed to Test Step 2.
2. Check the Operation of the SCR Catalyst Inlet Temperature Sensor
Note : Only perform this step on a cold engine.
A. Remove the SCR catalyst inlet temperature sensor and allow the sensor to rest in ambient air for 2 minutes.
B. Connect to the ECM by using Cat ET.
C. Monitor the value of the SCR catalyst inlet temperature sensor on Cat ET.
Sensor
Result : The value of the SCR catalyst inlet temperature sensor is within 9° C (15° F) of ambient temperature.
Repair : Reinstall the sensor. torque the sensor to the proper specification.
For a 4360-16 or E946 (2) code, proceed to Test Step 4.
For a 4360-17, E947 (1), 4360-18 or E947 (2) code, proceed to Test Step 3.
Result : The value of the SCR catalyst inlet temperature sensor is not within 9° C (15° F) of ambient temperature.
Repair : Replace the SCR catalyst inlet temperature sensor.
Proceed to Test Step 5.
3. Check for Exhaust Leaks
A. Start the engine.
B. Check the exhaust system for proper installation.
C. Check for proper installation of the exhaust system insulation.
D. Inspect the exhaust system between the DPF and the SCR for signs of an exhaust leak.
E. Inspect the SCR inlet temperature sensor to ensure proper installation in the sensor port.
Exhaust Leaks
Result : There were exhaust leaks found.
Repair : Repair or replace the component that is causing an exhaust leak.
Proceed to Test Step 5.
4. Check the Diesel Exhaust Fluid (DEF) Quality.
A. Measure the DEF quality. Refer to the Testing and Adjusting, "Diesel Exhaust Fluid Quality - Test" for the correct procedure.
DEF Quality
Result : The DEF is not contaminated.
Repair : Check the exhaust system for fuel. Refer to Troubleshooting, "Exhaust System Contains Fuel".
Contact the Dealer Solution Network (DSN) for authorization to replace the DOC, DPF, DEF Injector, and the SCR catalyst. Refer to Special Instruction, REHS8180 and the Disassembly and Assembly for more information.
Proceed to Test Step 5.
Result : The DEF is contaminated.
Repair : Contact the DSN for authorization to replace the DEF tank, DEF tank header and filters, all DEF lines, DEF pump, DEF injector, and the SCR catalyst. Refer to Special Instruction, REHS8180 and the Disassembly and Assembly for more information.
Proceed to Test Step 5.
5. Perform the "Aftertreatment System Functional Test"
A. Start the engine.
B. Connect to the ECM using Cat ET.
C. Perform the "Aftertreatment System Functional Test".
"Aftertreatment System Functional Test"
Result : The test was successful.
Return the unit to service.
Result : The test was not successful. There are more diagnostic codes.
Repair : Troubleshoot the diagnostic codes that are active. Refer to the Troubleshooting guide for the correct troubleshooting procedure.
Verify that the problem has been resolved.
If this procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solution Network (DSN).