828739 Control panel Volvo.Penta
AD30A; AQAD30A; MD30A, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C,
Control
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
ALEXRIMS ATIOT6535 828739 End Cap Silver 142mm Bearing Kit Rear Hub for VED6
RITEWAY (ライトウェイ) 142mm || Rear Hub || For VED6
RITEWAY (ライトウェイ) 142mm || Rear Hub || For VED6
19-10-2019
-: -
TCI America: Pentafluorophenylhydrazine, P0852-25G, 98.0% (GC,T)
CAS: 828-73-9 / Molecular Formula: C6H3F5N2 || MDL Number: MFCD00007574 || Laboratory research chemicals & materials || Fulfilled by the supplier, TCI America || TCI chemicals are for research and not intended for human or animal use.
CAS: 828-73-9 / Molecular Formula: C6H3F5N2 || MDL Number: MFCD00007574 || Laboratory research chemicals & materials || Fulfilled by the supplier, TCI America || TCI chemicals are for research and not intended for human or animal use.
Compatible models:
AD30A; AQAD30A; MD30A
AQ131A; AQ131B; AQ131C
AQ145B
AQ151A; AQ151B; AQ151C
AQ171A; AQ171C
AQ200D; AQ200F; 280B
AQ205A; AQ205LB
AQ211A; DP-A; SP-A
AQ225D; AQ225E; AQ225F
AQ231A; AQ231B; AQ231LB
AQ260A; AQ260B; BB260A
AQ271A; AQ271B; AQ271C
AQ290A
AQ311A; AQ311B
MD31A; TMD31A; TMD31B
MD31A; TMD31B; TAMD31B
MD40A; TMD40A; TMD40B
TMD41A; TMD41B; D41A
TMD41B; D41B; TAMD41B
Volvo.Penta
Volvo Penta entire parts catalog list:
AQ131A; AQ131B; AQ131C; AQ131D
AQ145B
AQ151A; AQ151B; AQ151C
AQ171A; AQ171C
AQ200D; AQ200F; 280B; 290A; 290DP
AQ205A; AQ205LB
AQ211A; DP-A; SP-A; 290A
AQ225D; AQ225E; AQ225F; BB225A; BB225AV; BB225B; BB225C; 275; 280B; 290A; 290DP; MS3B; MS3C; MS4A
AQ231A; AQ231B; AQ231LB; 290A; DP-A; SP-A; 275A; 285A
AQ260A; AQ260B; BB260A; BB260AV; BB260B; BB260C
AQ271A; AQ271B; AQ271C; AQ271D; AQ271LB
AQ290A
AQ311A; AQ311B
MD31A; TMD31A; TMD31B; TAMD31A; TAMD31B; AD31; AQAD31A; AD31B; 290A; DP-A; DP-B; DP-A1; DP-B1; SP-A; SP-A1
- Hydraulic Pump, Trim Instrument and Installation Components
- Hydraulic Pump, Trim Instrument and Installation Components
MD40A; TMD40A; TMD40B; TMD40C; AQD40A; TAMD40A; TAMD40B; AD40B; AQAD40A; AQAD40B
TMD41A; TMD41B; D41A; D41B; TAMD41A; TAMD41B; AQAD41A; AD41A; AD41B; 290A; DP-A; DP-B; DP-A1; DP-B1; SP-A; SP-A1; AD41BJ; AD41; AD41P-B; D41; TAMD41
- Hydraulic Pump, Trim Instrument and Installation Components
- Hydraulic Pump, Trim Instrument and Installation Components
Information:
Illustration 1 g00770279
SchematicTest Step 1. Inspect Electrical Connectors and Wiring
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect the J1/P1 ECM connector, J3/P3 machine connector, and all other connectors in the wiring harness. Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.Expected Result:All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, of abrasion, and of pinch points. All connections and grounds are tight and free of corrosion.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Shorts in the Harness from the ECM to the Digital Sensor
Illustration 2 g00938902
P1 ECM connector
Disconnect the J1/P1 ECM connector and the digital sensor.
Measure the resistance between P1:35 (Digital Sensor +8 VDC) and engine ground.
Measure the resistance between P1:35 (Digital Sensor +8 VDC) and P1:29 (Digital Sensor Return).Expected Result:The resistance is greater than 20,000 Ohms for each measurement.Results:
OK - Proceed to Test Step 3.
Not OK - There is a short between the ECM and the sensor.Repair: Repair the circuit.STOPTest Step 3. Check for Open Circuits in the Harness Between the ECM and the Digital Sensor
Illustration 3 g00938902
J1/P1 breakout
Turn the keyswitch to the OFF/RESET position and install a 7X-1715 Adapter Cable (40 Pin Breakout T) at ECM connector J1/P1.
Use a suitable piece of wire to short P1:35 (Digital Sensor +8 VDC) and P1:29 (Digital Return) at the breakout.
Disconnect the digital sensor.
Measure the resistance between terminal A (+8 VDC) and terminal B (Ground) of the connector for the digital sensor.
Remove the wire short from the breakout.Expected Result:The resistance is less than 10 Ohms for each measurement.Results:
OK - Proceed to Test Step 4.
Not OK - There is an open circuit in the wiring harness between the sensor and the ECM.Repair: Repair the circuit.Verify that the repair eliminates the problem.STOPTest Step 4. Check the Digital Sensor Supply Voltage at the Sensor Connector
Disconnect the digital sensor.
Turn the keyswitch to the ON position.
Measure the voltage across terminal A (+8 VDC) and terminal B (Ground) of the connector for the digital sensor.Expected Result:The digital sensor supply voltage is 8.0 0.5 VDC.Results:
OK - The supply voltage is reaching the sensor. Proceed to Test Step 5.
Not OK - The supply voltage is not reaching the sensor. Proceed to Test Step 7.Test Step 5. Check the Digital Sensor for an Internal Short
Illustration 4 g00938902
J1/P1 breakout
Disconnect the digital sensor.
Turn the keyswitch to the ON position.
Reconnect the digital sensor while you observe the voltage across P1:35 (Digital Sensor +8 VDC) and P1:29 (Digital Sensor Return) at the breakout.Expected Result:The supply voltage is 8.0 0.5 VDC. The voltage should not drop when the sensor is connected.Results:
OK - The sensor does not have an internal short.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The sensor may have an internal short. Proceed to Test Step 6.Test Step 6. Temporarily Install a New Sensor
Illustration 5 g00938902
J1/P1 breakout
Disconnect the suspect sensor and remove the suspect sensor.
Temporarily install a new sensor.
Turn the keyswitch to the ON position.
Observe the voltage across P1:35 (Digital Sensor +8 VDC) and P1:29 (Digital Sensor Return) at the breakout while you connect the new sensor.Expected Result:The supply voltage is 8.0 0.5 VDC. The voltage does not drop when the sensor is connected.Results:
OK - The suspect sensor was faulty.Repair: Permanently install the new sensor.STOP
Not OK - The sensor and the circuit appear to be OK at this time.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOPTest Step 7. Check the Digital Sensor Supply Voltage at the ECM
Illustration 6 g00938902
J1/P1 breakout
Disconnect the digital sensor.
Turn the keyswitch to the ON position.
Measure the voltage across P1:35 (Digital Sensor +8 VDC) and P1:29 (Digital Sensor Return) at the breakout.Expected Result:The supply voltage is 8.0 0.5 VDC.Results:
OK - The ECM is supplying the correct voltage.Repair: Refer to Troubleshooting, "Electrical Connectors - Inspect" if the problem is intermittent.STOP
Not OK - The ECM is not supplying the correct voltage.Repair: Verify your results.Replace the ECM. Refer to Troubleshooting, "Replacing the ECM" before replacing the ECM.Verify that the repair eliminates the problem.STOP
Parts control Volvo Penta:
1140186
1140186 Control cable
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ125B, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C
1140202
1140202 Control cable
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, A
1140109
1140109 Control cable
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A M
851601
851601 Control
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C,
804458
804458 Control cable
AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ145A; BB145A, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B
814023
814023 Control cable
AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ145A; BB145A, AQ175A, AQ190A; AQ240A, AQ200B; AQ225B, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ211A; DP-A; SP-A, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; A
845754
845754 Control sleeve
AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, MD31A; TMD31A; TMD31B, MD31A; TMD31B; TAMD31B, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A, TMD41A; TMD41B; D41A, TMD41B; D41B; TAMD41B
853846
853846 Control panel
230A; 230B; 250A, 430; 430A; 430B, 740A; BB740A, KAD42A; KAMD42A; HS1A, MD31A; TMD31B; TAMD31B, TMD41B; D41B; TAMD41B