844276 Control valve Volvo.Penta
D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, TAMD103A, TAMD122A; TMD122A; TAMD122P-A, TD100G; TD100G-85; TD100G-87, TID120FPP; TID120FG; TD120G, TMD100C, TMD102A; TAMD102A; TAMD102D, TMD121C; TAMD121C; TAMD121D
Control
Price: query
Rating:
Compatible models:
Volvo Penta entire parts catalog list:
D120A; D120AK; TD120A; TD120AG; TD120AG PP; TD120AK
D70B; D70B PP; D70B K; TD70B
TAMD103A
TAMD122A; TMD122A; TAMD122P-A; TAMD122P-B; TAMD122P-C; TMD122A/C; TAMD122AF
TD100G; TD100G-85; TD100G-87; TD100GG; TD100GG-85; TD100GG-87; TD100GGP-87; TD100HP-87; TD100HPB-87; TD100GP; TD100GP-85; TD100GGP; TID100K;
- Hydraulic Pump and Control Valve with Installation Components
- Hydraulic Pump and Control Valve with Installation Components
TMD100C
TMD102A; TAMD102A; TAMD102D
TMD121C; TAMD121C; TAMD121D; TAMD122C; TAMD122D
Information:
start by: a) remove turbocharger 1. Install the turbocharger on tool (A).2. Put marks on the housings for correct installation at assembly.3. Loosen clamp (1). Remove compressor housing (2). Remove the clamp. 4. Remove bolts (3), locks (6) and plates (5).5. Remove the center section from turbine housing (4). 6. Install tool (C) in tool (B). Install the center section in tool (C) as shown.7. Remove nut (7) that holds the impeller to the shaft and wheel assembly. 8. Install tool (E) on tool (D). Heat tool (D) to 350°F (177°C). Install the impeller on tool (E).
Make sure only the impeller is in the hot oil.
9. Install tool (E) with the center section on tool (F). Remove impeller (9) with an arbor press (8) and tool (G). Step 9 must be done before the impeller gets cold. 10. Remove shaft and wheel assembly (10), shroud (11) and spacer (13) from center housing (12). 11. Remove bolts (14), locks (15) and plate (16) from the center housing. 12. Remove collar (17). 13. Remove two bearings (18) and three snap rings (19) from the center housing.Assemble Turbocharger (Precombustion Chamber)
1. Clean all parts thoroughly before assembly. 2. Install snap ring (15), bearing (12) and snap ring (11) in center housing (10). Install snap ring (9) and bearing (8). Put 4L7464 Silicone Grease in the seal ring groove of the shaft and wheel assembly. Make sure it fills approximately one half or more of the groove depth for the complete circumference of the groove. Install ring seal (14) on the shaft and wheel assembly.3. Install shroud (13) and shaft and wheel assembly (16) in the center housing.
Use caution not to cause damage to ring seal (14) when the shaft and wheel assembly are installed.
4. Install spacer (7) and collar (6).5. Put plate (5) in position on the center housing. Install bolts (4). Tighten the bolts to a torque of 35 5 lb.in. (4.0 0.6 N m).6. Install spacer (3). Make sure the small inside diameter of the spacer is toward the impeller end of the shaft and wheel assembly.
If spacer (3) is installed with its small inside diameter toward the center housing it will cause a restriction of oil flow to the chamber and rings. This will cause a failure to the turbocharger.
7. Heat impeller (1) in oil to a maximum temperature of 350°F (177°C). Install the impeller on the shaft and wheel assembly. 8. Install tool (C) in tool (B). Instll the center section in tool (C). Install nut (2). Tighten the nut to a torque of 120 lb.in. (13.6 N m). Let the temperature of the impeller get below 150°F (65°C). Loosen the nut. Put a light amount of oil on the threads of the shaft and wheel assembly. Tighten the nut again to a torque of 30 lb.in. (3.4 N m). Put a mark on the nut and impeller. Tighten the nut 120° past the mark.
Do not put a bending force on the shaft and wheel assembly when nut (2) is tightened.
9. Install turbine housing (17) on tool (A). Install the center section in the turbine housing. Put the marks that were made at disassembly in alignment to make sure the housings are in their original position. 10. Put 5P3931 Anti-Seize Compound on the threads of bolts (21). Install plates (20), locks (19) and the bolts. Tighten the bolts to a torque of 175 15 lb.in. (19.8 1.7 N m).11. Install a new O-ring seal (18) on the center housing. 12. Put clamp (23) over the center section. Put compressor housing (22) in alignment with the marks made at disassembly. Put the clamp in position over the housing. Tighten the clamp to a torque of 120 10 lb.in. (13.6 1.1 N m).13. Put oil in the center section and turn the shaft and wheel assembly.end by: a) install turbocharger
Make sure only the impeller is in the hot oil.
9. Install tool (E) with the center section on tool (F). Remove impeller (9) with an arbor press (8) and tool (G). Step 9 must be done before the impeller gets cold. 10. Remove shaft and wheel assembly (10), shroud (11) and spacer (13) from center housing (12). 11. Remove bolts (14), locks (15) and plate (16) from the center housing. 12. Remove collar (17). 13. Remove two bearings (18) and three snap rings (19) from the center housing.Assemble Turbocharger (Precombustion Chamber)
1. Clean all parts thoroughly before assembly. 2. Install snap ring (15), bearing (12) and snap ring (11) in center housing (10). Install snap ring (9) and bearing (8). Put 4L7464 Silicone Grease in the seal ring groove of the shaft and wheel assembly. Make sure it fills approximately one half or more of the groove depth for the complete circumference of the groove. Install ring seal (14) on the shaft and wheel assembly.3. Install shroud (13) and shaft and wheel assembly (16) in the center housing.
Use caution not to cause damage to ring seal (14) when the shaft and wheel assembly are installed.
4. Install spacer (7) and collar (6).5. Put plate (5) in position on the center housing. Install bolts (4). Tighten the bolts to a torque of 35 5 lb.in. (4.0 0.6 N m).6. Install spacer (3). Make sure the small inside diameter of the spacer is toward the impeller end of the shaft and wheel assembly.
If spacer (3) is installed with its small inside diameter toward the center housing it will cause a restriction of oil flow to the chamber and rings. This will cause a failure to the turbocharger.
7. Heat impeller (1) in oil to a maximum temperature of 350°F (177°C). Install the impeller on the shaft and wheel assembly. 8. Install tool (C) in tool (B). Instll the center section in tool (C). Install nut (2). Tighten the nut to a torque of 120 lb.in. (13.6 N m). Let the temperature of the impeller get below 150°F (65°C). Loosen the nut. Put a light amount of oil on the threads of the shaft and wheel assembly. Tighten the nut again to a torque of 30 lb.in. (3.4 N m). Put a mark on the nut and impeller. Tighten the nut 120° past the mark.
Do not put a bending force on the shaft and wheel assembly when nut (2) is tightened.
9. Install turbine housing (17) on tool (A). Install the center section in the turbine housing. Put the marks that were made at disassembly in alignment to make sure the housings are in their original position. 10. Put 5P3931 Anti-Seize Compound on the threads of bolts (21). Install plates (20), locks (19) and the bolts. Tighten the bolts to a torque of 175 15 lb.in. (19.8 1.7 N m).11. Install a new O-ring seal (18) on the center housing. 12. Put clamp (23) over the center section. Put compressor housing (22) in alignment with the marks made at disassembly. Put the clamp in position over the housing. Tighten the clamp to a torque of 120 10 lb.in. (13.6 1.1 N m).13. Put oil in the center section and turn the shaft and wheel assembly.end by: a) install turbocharger
Parts control Volvo Penta:
1140186
1140186 Control cable
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ125B, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C
888082
888082 Control cable
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D16C-A MH; D16C-B MH; D16C-C MH, D16
888090
888090 Control cable
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D16C-A MH; D16C-B MH; D16C-C MH, D16
1140115
1140115 Control cable
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A M
21633517
21633517 Control cable
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D16C-A MH; D16C-B MH; D16C-C MH, D16C-D MH, D2-55;
1140142
1140142 Control cable
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D12D-A MH; D12D-B MH; D12D-C MH, D13B-E MH; D13B-E MH (FE); D13B-N MH, D16C-A MH; D16C-B MH; D16C-C MH, D16
853200
953942
953942 Control rod
D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, MD120A; MD120AK; TMD120A