21350611 Volvo.Penta Coolant pipe

Illustration 1 g06151593
Schematic of the diagnostic connector and the data link connector for a diagnostic connector that is mounted off engine
Illustration 2 g06151589
Schematic of the diagnostic connector and the data link connector for an engine-mounted diagnostic connector
Illustration 3 g02028056
P1 pin locations for the diagnostic connector
(8) Data link +
(9) Data link -
Illustration 4 g02090413
Typical view of the P2 pin locations for the diagnostic connector
(20) Data link +
(28) Data link -
(53) Voltage supply (diagnostic connector)
(54) Return (diagnostic connector)Complete the procedure in the order in which the steps are listed.
Table 1
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Inspect the connectors in the circuit for the data link.
Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
C. Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
D. Check the screw for the P1 and P2 ECM connectors for correct torque of 6 N m (53 lb in).
E. Check all the wiring associated with the data link for abrasions and pinch points.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: A damaged wire or damaged connector was not found.
Proceed to Test Step 2.
2. Determine the Type of Fault in the Data Link
A. Connect the electronic service tool to the diagnostic connector that is on the engine harness or on the application.
Repair: Turn the keyswitch to the ON position.
Power to the comms adapter
Result: The power lamp illuminates on the communications adapter. The communications adapter is receiving the correct voltage.
Proceed to Test Step 5.
Result: The power lamp is not illuminated on the communications adapter. The communications adapter is not currently receiving the correct voltage.
Proceed to Test Step 3.
3. Check the Battery Voltage at the Diagnostic Connector
A. Turn the keyswitch to the ON position.
B. Use a multimeter to measure the voltage from pin A (battery+) and pin B (ground) of the diagnostic connector.
11.0 VDC and 13.5 VDC for a 12 VDC system. 22.0 VDC and 27.0 VDC for a 24 VDC system.
Result: The voltage is between 22.0 VDC and 27.0 VDC for a 24 V system. The voltage is between 11.0 VDC and 13.5 VDC for a 12 V system. The diagnostic connector is receiving the correct voltage.
Proceed to Test Step 5.
Result: The voltage is not between 22.0 VDC and 27.0 VDC for a 24 V system. The voltage is not between 11.0 VDC and 13.5 VDC for a 12 V system. The diagnostic connector is not currently receiving the correct voltage.
Proceed to Test Step 4.
Illustration 5 g03705906
Typical view of the diagnostic connector from the wire side
(A) Switched battery +
(B) Battery ground (GND)
(D) Data link +
(E) Data link -
Table 2
Troubleshooting Test Steps Values Results
4. Bypass the Wiring for the Diagnostic Connector
A. Disconnect the wires from pin A and pin B of the diagnostic connector.
Note: If the diagnostic connector is mounted on the engine, perform Steps B to D. If the diagnostic connector is mounted off the engine, perform Step E.
B. Disconnect the wires from P2:53 and P2:54.
C. Fabricate a jumper wire to connect pin A of the diagnostic connector to P2:53.
D. Fabricate a jumper wire to connect pin B of the diagnostic connector to P2:54.
E. Fabricate a jumper wire to connect pin "A" of the diagnostic connector to battery+ and pin "B" to the battery-.
F. Connect the electronic service tool to the diagnostic connector that is on the engine harness or on the application.
G. Turn the keyswitch to the ON position. The power lamp should illuminate on the communications adapter.
Other devices are OK
Result: The power lamp is illuminated. The fault is in the harness.
Repair: Repair the faulty harness or replace the faulty harness.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The power lamp is not illuminated.
Proceed to Test Step 6.
5. Check the Data Link Connections
A. Turn the keyswitch to the OFF position.
B. Disconnect the communications adapter from the diagnostic connector.
C. If the diagnostic connector is installed on the application, disconnect connector P1 from the ECM. Check the resistance between P1:8 and pin "D" on the diagnostic connector. Check the resistance between