837072 Coolant pipe Volvo.Penta
MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
Coolant
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
MD70B; MD70BK; TMD70B
MD70C; TMD70C; TAMD70C
Volvo.Penta
Volvo Penta entire parts catalog list:
MD70C; TMD70C; TAMD70C; THAMD70C; AQD70BL; AQD70CL
Information:
start by: a) remove timing gear cover and oil pump1. Remove the plug from the fuel injection pump housing and install timing pin (A).2. While turning the crankshaft clockwise as seen from the front of the engine, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft.3. Remove the tachometer drive adapter shaft and install tooling (B) as follows: a) Install bolt assembly (2) in the fuel injection pump camshaft. The bolt assembly must turn freely into the camshaft. Do not use force to install the bolt assembly.b) Install bolt (1) in the gear.c) Tighten the bolt and remove gear (3). 4. Remove screw (4), washer (5), and gear (6) from the camshaft. 5. Install tooling (C) and remove gear (7) from the camshaft.Install Camshaft Gears (Engines With Taper Drive For Fuel Injection Pump)
Do not heat the gear for the camshaft with a torch or to a temperature of more than 400°F (204°C). Higher temperatures can cause the dowels to loosen and come out of the gear. Do not use force to install the gear. Damage to the camshaft or camshaft thrust pin can be the result.
1. Heat the large gear for the camshaft to a maximum temperature of 400°F (204 C). Put the groove (slot) on the gear in alignment with the dowel on the camshaft and install the gear so the timing marks on the camshaft gear and crankshaft gear are in alignment.
GEARS SHOWN OUT OF ENGINE FOR BETTER PHOTO ILLUSTRATION2. Put gear (1) in position on the dowels. Put pin (4) on washer (3) in alignment with hole (2) and install the washer.
GEARS SHOWN OUT OF ENGINE BETTER PHOTO ILLUSTRATION3. Install screw (5). Tighten the screw to a torque of 108 36 lb.in. (124.5 41.5 cm.kg). Put marks (stake) on the screw in two places with a hammer and punch. 4. Put gear (7) for the fuel injection pump camshaft in position and install tachometer drive adapter shaft (6). Tighten the shaft to a torque of 32 2 lb.ft. (4.4 0.3 mkg).5. After the timing gear cover has been installed, check the timing as follows: a) Remove timing pin (A).b) Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c) While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft. d) Remove plug (8) from the timing hole. Remove bolt (9) and install it through the timing hole and into the camshaft gear. The timing is correct when timing pin (A) is installed in the fuel injection pump camshaft and bolt (9) is installed in the camshaft gear.e) Remove the bolt and install the plug. Remove timing pin (A) and install the plug. If the bolt can not be installed, the timing must be corrected as follows: a) With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b) Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (9) can be installed. Install the bolt.c) Install tachometer drive adapter shaft and tighten it to a torque of 32 2 lb.ft. (4.4 0.3 mkg). Install the adapter housing. Remove the bolt and timing pin and install the plugs.end by: a) install timing gear cover and oil pump
Do not heat the gear for the camshaft with a torch or to a temperature of more than 400°F (204°C). Higher temperatures can cause the dowels to loosen and come out of the gear. Do not use force to install the gear. Damage to the camshaft or camshaft thrust pin can be the result.
1. Heat the large gear for the camshaft to a maximum temperature of 400°F (204 C). Put the groove (slot) on the gear in alignment with the dowel on the camshaft and install the gear so the timing marks on the camshaft gear and crankshaft gear are in alignment.
GEARS SHOWN OUT OF ENGINE FOR BETTER PHOTO ILLUSTRATION2. Put gear (1) in position on the dowels. Put pin (4) on washer (3) in alignment with hole (2) and install the washer.
GEARS SHOWN OUT OF ENGINE BETTER PHOTO ILLUSTRATION3. Install screw (5). Tighten the screw to a torque of 108 36 lb.in. (124.5 41.5 cm.kg). Put marks (stake) on the screw in two places with a hammer and punch. 4. Put gear (7) for the fuel injection pump camshaft in position and install tachometer drive adapter shaft (6). Tighten the shaft to a torque of 32 2 lb.ft. (4.4 0.3 mkg).5. After the timing gear cover has been installed, check the timing as follows: a) Remove timing pin (A).b) Turn the crankshaft clockwise as seen from the front of the engine approximately 1/2 turn. Install timing pin (A) again.c) While turning the crankshaft clockwise, push on timing pin (A) until it slides into the groove (slot) in the fuel injection pump camshaft. d) Remove plug (8) from the timing hole. Remove bolt (9) and install it through the timing hole and into the camshaft gear. The timing is correct when timing pin (A) is installed in the fuel injection pump camshaft and bolt (9) is installed in the camshaft gear.e) Remove the bolt and install the plug. Remove timing pin (A) and install the plug. If the bolt can not be installed, the timing must be corrected as follows: a) With timing pin (A) installed, remove the tachometer drive adapter housing and shaft.b) Loosen the gear from the fuel injection pump camshaft. Turn the crankshaft clockwise approximately two full turns until bolt (9) can be installed. Install the bolt.c) Install tachometer drive adapter shaft and tighten it to a torque of 32 2 lb.ft. (4.4 0.3 mkg). Install the adapter housing. Remove the bolt and timing pin and install the plugs.end by: a) install timing gear cover and oil pump
Parts coolant Volvo Penta:
1141523
1141523 Coolant
AD30A; AQAD30A; MD30A, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ260A; AQ260B; BB260A, AQ290A, MD40A; TMD40A; TMD40B, MD70B; MD70BK; TMD70B, TAMD60C, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP, TID121FG
1141524
1141524 Coolant
AD30A; AQAD30A; MD30A, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ260A; AQ260B; BB260A, AQ290A, MD40A; TMD40A; TMD40B, MD70B; MD70BK; TMD70B, TAMD60C, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP, TID121FG
1141525
1141525 Coolant
AD30A; AQAD30A; MD30A, AQ200D; AQ200F; 280B, AQ205A; AQ205LB, AQ260A; AQ260B; BB260A, AQ290A, MD40A; TMD40A; TMD40B, MD70B; MD70BK; TMD70B, TAMD60C, TD60D; TD60D-83; TD60DPP-83, TD70G; TD70G-83; TD70GPP, TID121FG
837952
837664
837665
837910
837873