872293 Volvo.Penta Countershaft


872293 Countershaft Volvo.Penta DPX-S; DPX-S1; DPX-S 1.59, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A Countershaft
872293 Countershaft Volvo Penta
Rating:
13

Buy Countershaft 872293 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$19.95
 

27-03-2024
0.2645[0.12] pounds
US: Rutmonkey
Domino Pair of Trial Knobs Black/Red (Motorcycle Knobs) / Couple of Trial Hand Grip, Black/Red (Knobs Motorcycle)
DOMINO Sold in Pairs || Trials competition grip || Domino dedicated it’s best engineers to develop the ultimate combination of grip and comfort for the rider who measures his ride in days, not hours. The diamond, dimple pattern offers a sure grip that is easy on the hands. || Over 50 years of development have led to the DOMINO proprietary rubber compound. || The compound is medium-to-soft with durability unmatched by grips of similar firmness.
Number on catalog scheme: 9
 

Volvo Penta entire parts catalog list:

DPX-S; DPX-S1; DPX-S 1.59; DPX-S 1.68; DPX-S 1.78; DPX-S1 1.59; DPX-S1 1.68; DPX-S1 1.78; TSK DPX-C
KAD42B; KAMD42B; TAMD42B
KAD42P-A; KAMD42P-A; HS1A

Information:


Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01283374Note: Mark the positions of the engine supports and the shims for proper installation. The right side engine supports are connected to the plates on the generator base by dowels. The dowels must be removed before the mounting supports can be removed.
Remove the plastic caps from the engine supports to the access hole for the dowels. Use a 1/2 inch bolt with a washer in order to remove the dowels, if necessary.
Attach a suitable lifting device to the engine lifting brackets. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb).
Remove bolts (1) that hold engine supports (2) to the generator base. Check the O-ring seals on the bolts for damage. If necessary, replace the O-ring seals. The O-ring seals should be installed on clean bolts.
Lift the engine enough in order to place a suitable lifting device around engine support (2). Use the forcing bolt in order to help lift the engine. The weight of each engine support (2) is approximately 60 kg (130 lb).
Remove the shims, if necessary.
Remove bolts (3) that hold engine support (2) to the cylinder block.
Tap engine support (2) with a rubber mallet in order to loosen dowels (4) from the cylinder block.
Remove engine support (2) from the side of the cylinder block.
If necessary, remove dowels (4) from engine support (2). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01283374
If dowels (4) were removed from engine support (2), install the dowels. The dowels must extend 20.0 1.0 mm (0.79 0.04 inch) above the surface of engine support (2). Check the O-ring seals for damage. If necessary, replace the O-ring seals.
Use a suitable lifting device to place engine support (2) in position on the side of the cylinder block. The weight of each engine support (2) is approximately 60 kg (130 lb). Install bolts (3). Tighten the bolts to a torque of 1125 100 N m (830 75 lb ft).
Install the shims in the original location, if necessary.
Install the dowels through engine support (2) and into the base on the right side of the engine, if necessary.
Lower the engine onto the base assembly. The weight of the 3606 Engine is approximately 15700 kg (34600 lb). The weight of the 3608 Engine is approximately 19000 kg (41900 lb). Remove the forcing bolt when you lower the engine. Install bolts (1).
Check the alignment between the engine and the driven equipment.
Perform the following check for soft foot:
Soft foot is measured with a dial indicator. Mount a dial indicator from the base assembly to the top of the foot next to the engine block. Be sure that all the jacking screws are loose. While one foot at a time is loosened, the deflection of the foot must not change more than 0.076 mm (0.0030 inch). If necessary, add shims in order to eliminate the soft foot. Repeat the procedure for the soft foot until all the feet are measured for compliance with specifications. If necessary, add shims under the feet in order to eliminate gaps. When possible, avoid using shims under the foot with the slider block. Do not trim the shims. The addition of shims is required in order to provide equal loading on each foot. This equalization prevents unnecessary stresses in the welds and the components.
Replace the plastic cap on the access hole for the dowels on engine support (2). End By:
Remove the engine lifting brackets. Refer to Disassembly and Assembly, "Engine Lifting Bracket - Remove and Install".


Parts countershaft Volvo Penta:

854611
 
854611 Countershaft
430; 430A; 430B, 500; 500A; 501A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, DP-C1; DP-D1; DP-S, DP-E; SP-E; TSK DP-E, DP-G; TSK DP-G, KAD42A; KAMD42A; HS1A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; H
Back to top