861924 Volvo.Penta Cover


861924 Cover Volvo.Penta MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B Cover
861924 Cover Volvo Penta
Rating:
53

Buy Cover 861924 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 6
 

Compatible models:

Volvo Penta entire parts catalog list:

MD2010A; MD2020A; MD2030A; MD2040A; MS2B-R; MS2A-D; MS2A-E; MS2L-D; MS2L-E; 120S-D; 120S-E; MD2010; MD2030; MD2040; MD2020
MD2010B; MD2020B; MD2030B; MD2040B; MS2L-D; MS2A-D; 120S-D; MS2B-R; MS2A-E; MS2L-E

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 298-5564 T40 Torx Socket 1
B 268-1968 Pry Bar 1
C 370-8376 Plugs and Caps 1 Start By:
Remove the rocker shaft assembly.
Remove the fuel injection lines.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorised personnel that have the correct training.Before begining ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information.Refer to Systems Operation, Testing and Adjusting Manual, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Use a deep socket in order to remove the electrical connections from the electronic unit injectors. Use of incorrect tooling will result in damage to the electronic unit injectors.
Turn the fuel supply to the OFF position.
Turn the battery disconnect switch to the OFF position.
Illustration 1 g03364219
Make a temporary mark on valve bridges (2) to show the location and orientation. Remove valve bridges (2). Note: Identification will ensure that the valve bridges can be reinstalled in the original location and the original orientation.
Remove seal (1) from the cylinder head and electronic unit injector (5).
Make a temporary mark on harness assembly (3) to show the correct location and orientation.
Remove harness assembly (4) from electronic unit injector (5).
Use Tooling (A) to remove bolt (6) from clamp (7). Discard bolt (6). Note: Tooling (A) must be used to ensure no damage to the electronic unit injector.
Illustration 2 g03364220
Illustration 3 g03364222
Make a temporary mark on electronic unit injector (5) to show the original location of the electronic unit injector.
Temporarily remove Tooling (C) from the electronic unit injector.
Use Tooling (B) to pry beneath clamp (7) and free electronic unit injector (5) from the cylinder head. Note: Always handle electronic unit injectors with care.
Immediately replace Tooling (C) onto the electronic unit injector.
If electronic unit injector (5) is to be reused, Follow Step 13 through Step 15 to remove sealing washer (9) and O-ring seal (8).
Use a suitable tool to remove sealing washer (9) from electronic unit injector (5). Ensure that the sealing washer is removed from the cylinder head. Note: Ensure that the nozzle for the electronic unit injector is not damaged in any way on removal of the sealing washer.
Install Tooling (C) to the nozzle for electronic unit injector (5) and the open port of the electronic unit injector.
Remove O-ring seal (8) from electronic unit injector (5).
If necessary, repeat Step 3 through Step 15 to remove the remaining electronic unit injector.
Illustration 4 g03364228
If necessary, follow Steps 17.a through 17.d to remove harness assemblies (3) from cylinder head (13).
remove cable straps (10).
Disconnect harness assembly (12) from harness assembly (3).
Remove bolt (11) for harness assembly (3).
Remove harness assembly (3) from cylinder head (13).
If necessary, repeat Step 17.a through Step 17.d to remove the remaining harness assemblies from the cylinder head.


Parts cover Volvo Penta:

828607
 
828607 Cover plate
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQD70D; TAMD70D; TAMD70E, D1-13; D1-13B; D1-20, D12D-A MH; D12D-B MH; D12D-C MH, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, D5A-T;
842722
Cover
842722 Cover
2001; 2001B; 2001AG, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42A; KAMD42A; HS1A, KAD42B; KAMD
1140046
 
1140046 Cover
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ125B, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C
850823
Cover
850823 Cover
2001; 2001B; 2001AG, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD201
850824
Cover
850824 Cover
AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C, KAD32P; TAMD42WJ-A; KAD43P-A, KAD42B; KAMD42B; TAMD42B, KAD42P-A; KAMD42P-A; HS1A, MD2010-C; MD2010-D; MD2020
851881
Cover
851881 Cover
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ125B, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ211A; DP-A; SP-A,
853713
Cover
853713 Cover
230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ125B, AQ131A; AQ131B; AQ131C, AQ145B, AQ151A; AQ151B; AQ151C, AQ171A; AQ171C, AQ205A; AQ205LB, AQ
3580326
 
3580326 Cover
MD2010A; MD2020A; MD2030A, MD2010B; MD2020B; MD2030B
Back to top