833813 Volvo.Penta Crankcase

Cross-Reference Information for Event Codes
Table 1 is a list of the event codes for the engine. The event codes are cross-referenced with the appropriate procedure that can be used to troubleshoot the code.Event codes are generated when abnormal operating conditions exist. A further explanation of event codes and the engine's monitoring system are described after Table 1.Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Table 1
Cross-Reference from Codes to Troubleshooting Procedure
Code Flash Code SPN Code Troubleshooting Procedure
E096(1) High Fuel Pressure 63 94-15 Troubleshooting, "Fuel Pressure Is High"
E096(2) High Fuel Pressure 94-16
E096(3) High Fuel Pressure 94-00
E360(1) Low Engine Oil Pressure 46 100-17 Troubleshooting, "Oil Pressure Is Low"
E360(2) Low Engine Oil Pressure 100-18
E360(3) Low Engine Oil Pressure 100-01
E361(1) High Engine Coolant Temperature 61 110-15 Troubleshooting, "Coolant Temperature Is High"
E361(2) High Engine Coolant Temperature 110-16
E361(3) High Engine Coolant Temperature 110-00
E362(1) Engine Overspeed 35 190-15 Troubleshooting, "Engine Overspeeds"
E362(2) Engine Overspeed 190-16
E362(3) Engine Overspeed 190-00
E363(1) High Fuel Supply Temperature 65 174-15 Troubleshooting, "Fuel Temperature Is High"
E363(2) High Fuel Supply Temperature 174-16
E363(3) High Fuel Supply Temperature 174-00
E539(1) High Intake Manifold Air Temperature 64 1636-15 Troubleshooting, "Inlet Air Temperature Is High"
E539(2) High Intake Manifold Air Temperature 1636-16
E539(3) High Intake Manifold Air Temperature 1636-00 Parts of the Event Code
Event Code - The "E" identifies the code as an event code. The "XXX(X)" represents a numeric identifier for the event code. The fourth "(X)" assigns one of three levels to the active event code according to the severity of the abnormal system condition. This is followed by a description of the code. Refer to the following example:
E360(1) Low Engine Oil Pressure
E360(2) Low Engine Oil Pressure
E360(3) Low Engine Oil PressureThree possible responses may be available for each parameter. Some of the responses are not available for some of the parameters. Refer to Table 2.
Table 2
Indicators (1), (2), and (3)
Warning Category Indicator Severity
(1) Least Severe
(2) Moderate Severity
(3) Most Severe The definition for the levels of severity for an event are defined below:Level (1) - Level (1) alerts the operator that the engine system requires attention. The operator should check the involved system condition or the operator should perform maintenance on the involved system at the earliest possible time.Level (2) - Level (2) requires a change in the operation of the engine or the performance of a maintenance procedure. Failure to correct the problem that causedthis warning may result in damage to the engine components.Level (3) - Level (3) requires an immediate safe shutdown of the engine in order to avoid damage to the engine or injury to personnel around the engine. The problem that caused the event must be corrected before engine operation can resume.Active Event Codes
An active event code represents a problem with engine operation. Correct the problem as soon as possible.Active event codes are listed in ascending numerical order. The code with the lowest number is listed first.Illustration 1 is an example of the operating range of a temperature sensor. Do not use the Illustration to troubleshoot temperature sensors.
Illustration 1 g01138880
Example of the typical operating range of a temperature sensor
(1) This area represents the normal operating range of the parameter. The normal output voltage of the sensor is between 0.2 VDC and 4.2 VDC.
(2) In this area, the temperature above 107 °C (225 °F) is higher than normal. The output voltage of the sensor will generate an event code. The sensor does not have an electronic problem.
(3) In these areas, the output voltage of the sensor is too high or too low. The voltage is outside of the normal range. The electronic problem will generate a diagnostic code. Refer to Troubleshooting, "Diagnostic Trouble Codes" for additional information on diagnostic codes.Logged Event Codes
When the ECM generates an event code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. The ECM will record the following information when an event code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeLogged events are listed in chronological order. The most recent event code is listed first.This information can be helpful for troubleshooting intermittent problems. Logged codes can also be used to review the performance of the engine.Clearing Event Codes
A code is cleared from memory when one of the following conditions occur:
The code does not recur for 100 hours.
A new code is logged and there are already ten codes in memory. In this case, the oldest code is cleared.
The service technician manually clears the code.Always clear logged event codes after investigating and correcting the problem which generated the code.Troubleshooting
For basic troubleshooting of the engine, perform the following steps in order to diagnose a malfunction:
Obtain the following information about the complaint:
The event and the time of the event
Determine the conditions for the event. The conditions will include the engine rpm and the load.
Determi