7726000_087 Volvo.Penta crankshaft and related parts


7726000_087 crankshaft and related parts Volvo.Penta 2001; 2001B; 2001AG crankshaft
7726000_087 crankshaft and related parts Volvo Penta
Rating:
63

Buy crankshaft and related parts 7726000_087 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

2001; 2001B; 2001AG   Volvo.Penta

Volvo Penta entire parts catalog list:

Information:

1. Remove tube and elbow (1).2. Remove tube and oil sump (2).
Turn the crankshaft so the piston is down, and remove the ridge of carbon with emery cloth from each liner before removing the pistons. Damage can be caused to the pistons during removal by the build up of carbon if it is not removed.
3. Turn the crankshaft until the connecting rod cap to be removed is at bottom center.4. Remove connecting rod cap (3) from the connecting rod.
Put identification marks on the connecting rod caps as to their location in the engine. Keep the caps with their respective piston.
5. Push the connecting rod and piston away from the crankshaft until the piston rings are above the cylinder liner. Remove piston (4) and the connecting rod from the engine.
Use tape to hold the bearing halves together and to identify the number of the cylinder.
Install Pistons
1. Turn the crankshaft until the bearing journal for the piston to be installed is at bottom center.2. Put clean engine oil on the crankshaft journal and on the inside of the cylinder liner.3. Put clean engine oil on the piston rings and connecting rod bearings.4. Move the piston ring gaps 180° apart.5. Use tool (A), and put the piston and connecting rod in its original location in the cylinder block. Be sure the numbered side of the connecting rod is toward the right side of the engine. This is when viewed from the front of the engine.
Be sure the connecting rod bolts do not contact the crankshaft journal during installation of the piston.
6. Use a hammer handle, and lightly tap the piston into position.
When the connecting rod caps are installed, make sure the number on the side of the cap is next to the same number on the connecting rod. The numbers must be away from the camshaft.
7. Install connecting rod cap (1) and the nuts which hold it. Tighten the nuts to a torque value of: Cadmium plated nuts (silver color) - 100 N m (75 lb.ft).Phosphated nuts (dull black color) - 130 N m (95 lb.ft.).8. Follow the same procedure for installation of the remainder of the pistons. 9. Install tube and elbow (2). Install tube and oil sump (3).END BY:a. install oil panb. install cylinder head assemblyDisassemble Pistons
START BY:a. remove pistons Put identification marks on all parts for correct assembly.1. Remove rings (1) from piston (2) with tool (A). 2. Remove retaining ring (3) from each side of the piston with tool (B).3. Remove pin (4) and connecting rod (5) from piston (2). 4. Remove bushing (6) from connecting rod (5) with tool group (C).5. Check all of the parts of the piston and rod for damage and wear. See Connecting Rods in Specifications.Assemble Pistons
1. Install the bushing in connecting rod (1) with tool group (A) and a press. See bushing dimensions in Specifications. The concave area (the part that makes the curve to the inside) in the piston is toward one side of the piston. Install the piston on the connecting rod with the concave area toward the side which has the connecting rod and cap identification on it.2. Slide connecting rod (1) inside the piston. Install pin (2) in the piston and the connecting rod. 3. Install a retaining ring (3) on each side of piston (4) with tool (B). 4. Install rings (5) on piston (4) with tool (C).END BY:a. install pistons


Parts crankshaft Volvo Penta:

7726000_085
7726000_084
7726000_090
7726000_089
7726000_094
7726000_098
876250
Crankshaft
876250 Crankshaft
2001; 2001B; 2001AG
876251
Crankshaft
876251 Crankshaft
2001; 2001B; 2001AG
Back to top