275059 Volvo.Penta Cylinder liner kit


275059 Cylinder liner kit Volvo.Penta MD120A; MD120AK; TMD120A, TD120AHC; TD120ARC; TAD120AHC, TD120C, TID120FPP; TID120FG; TD120G Cylinder
275059 Cylinder liner kit Volvo Penta
Rating:
43

Buy Cylinder liner kit 275059 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$41.99
 

22-12-2023
0.57 Kilograms
CN: Jonceen
Outdoor Pillows Waterproof Yellow Pillow Covers 24 x 24 inch Set of 4 Throw Pillows for Couch, Retro Throw Pillow Covers Linen Pillowcase Square Decorative Pillows for Outside Garden Patio S 492
Jonceen SIZE: 60 x 60 cm / 24 x 24 inches, Please allow 1~2cm deviation because of hand-cutting and sewing. || LINEN CUSHIONS: Cushion covers is made of durable waterproof linen fabric, wick away sweat, have good breathability, comfortable to the touch. NOTE: CUSHION COVERS ONLY, THE INNER NOT INCLUDED. || INVISIBLE ZIPPER: The delicately hidden zipper closer was designed to good look elegant, is a pet and toddler-friendly design, also very easy to insert and replace, with sturdy sewing and delicate stitched edges for extra durability. || DECORATIVE PILLOWS: A wide range of colors and double-sided pattern designs to give you a variety of decorative styles, perfect for home sofa accent decor cushions. suitable for living room, bedroom, sofa, couch, bed, car, office, cafe, etc. It can also be a lovely gift for family, lovers, or friends on festive days. || SERVICE: If you have anything questions, please send us an e-mail, and we will respond within 24 hours. We promise will check carefully before shipping, If there is any problem with damage when you receive your parcel, please provide us with pictures and we will send you a new one free of charge.
$52.20
 

26-07-2022

-: -
American Shifter 275059 Shift Knob (Blue Carpe Diem Green Stripe with M16 x 1.5 Insert)
Base Insert Threads: M16 X 1.5 || Design: Carpe Diem || Design Color: Blue || Shift Knobs Color: Green || Color: Green & White Stripe
$42.99
 

22-12-2023
1.0[0.45] pounds
US: Weldfabulous
Miller 275059 Label, Nameplate Maxstar 161 Sth (Rear)
Miller Electric
Number on catalog scheme: 1
 

Volvo Penta entire parts catalog list:

MD120A; MD120AK; TMD120A; TMD120AK; TAMD120A; TAMD120AK; TMD120B; TAMD120B; TAMD120B-CC
TD120AHC; TD120ARC; TAD120AHC; TD120BHC; TD120BRC; TAD120BHC; TAD120CHC; TD120AHC/CC; TD120ARC/CC
TD120C
TID120FPP; TID120FG; TD120G; TD120GG PP; TD120GG

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9832 Engine Rollover Stand 1
B 138-7576 Link Bracket 2
C 6V-4876 Lubricant -
D 8T-5096 Dial Indicator Gp 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01124614
Install plugs (11) and tighten to a torque of 50 7 N m (37 5 lb ft).
Position crankshaft gear (10) on the crankshaft and install bolts (9).
Illustration 2 g01124115Note: Install the main bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the main bearings for final assembly.
Install the upper half of main bearing (12) in the cylinder block. Ensure that the main bearing is installed so that the bearing tab fits into the notch in the cylinder block. Coat the main bearing with clean engine oil. Note: The upper half of the main bearing has an oil hole in the center.
Install the upper halves of connecting rod bearings (13) in the connecting rod assemblies. Coat the connecting rod bearing with clean engine oil.
Illustration 3 g01124538
Illustration 4 g01124192
Bolt tightening sequence for the main bearing caps
Note: Ensure that the word "FRONT" that is on the end of the crankshaft is toward the front of the engine.
Attach Tooling (B) and a suitable lifting device to each end of crankshaft (7). The weight of the 3516C crankshaft is approximately 800 kg (1765 lb). Position the crankshaft in the cylinder block.
Place clean engine oil on thrust plates (8). Install thrust plates (8) on each side of the center main bearing.
Install the lower half of the main bearing in the main bearing cap. Ensure that the main bearing is installed so that the bearing tab fits into the notch in main bearing cap (6). Coat the main bearing with clean engine oil.
Coat the underside of the bolt heads and the threads of bolts (5) with clean engine oil. Position main bearing caps (6) and install the bolts and washers. Do not tighten the bolts at this time. Note: The main bearing caps must be installed with the word "FRONT" and the part number toward the front of the engine. Each main bearing cap has a number on the bottom surface and each main bearing must be installed in the corresponding position in the cylinder block.
Tighten bolts (5) in sequence to a torque of 190 14 N m (140 10 lb ft).
Place an index mark on the bolts and the main bearing cap. Tighten the bolts for an additional 180 5 degrees (1/2 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Use Tooling (D) to measure the end play of the crankshaft. The end play must not exceed 0.17 to 0.63 mm (0.007 to 0.025 inch).
Illustration 5 g01124522
Illustration 6 g01124419
Bolt tightening sequence for the connecting rod caps
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Install the upper half of the connecting rod bearing on the connecting rod. Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod. Coat the connecting rod bearing with clean engine oil. Position the connecting rod onto a journal of the crankshaft.
Install the lower half of the connecting rod bearing on connecting rod cap (4). Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod cap. Coat the connecting rod bearing with clean engine oil. Note: The number that is on the side of the connecting rod caps must be installed next to the corresponding number that is on the side of the connecting rod. Install the chamfered side of the connecting rod cap next to the thrust surface of the crankshaft.Note: Reman connecting rods are not numbered for the cylinder position.
Apply Tooling (C) to the threads, the shank, and the seat of bolts (3).
Place connecting rod cap (4) into position. Install bolts (3). Use the following procedure to tighten the bolts:
Tighten Bolt (A) and Bolt (B) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) to a torque of 90 5 N m (65 4 lb ft).
Tighten Bolt (C) and Bolt (D) again to a torque of 90 5 N m (65 4 lb ft).
Place an index mark on the bolts and the connecting rod cap. Tighten each bolt for an additional 90 5 degrees (1/4 turn).
Rotate the crankshaft in order to ensure that the crankshaft turns freely.
Each counterweight is numbered and must be installed in the same position as the correspondin


Parts cylinder Volvo Penta:

7742190_004
 
7742190_004 cylinder block
MD120A; MD120AK; TMD120A
275060
 
275060 Cylinder liner kit
D120A; D120AK; TD120A, MD120A; MD120AK; TMD120A, TD120AHC; TD120ARC; TAD120AHC
275069
 
275069 Cylinder liner kit
MD120A; MD120AK; TMD120A, TD120AHC; TD120ARC; TAD120AHC
468749
Cylinder head
468749 Cylinder head
MD120A; MD120AK; TMD120A, TD120HPP; TID120HPP, TID120FPP; TID120FG; TD120G
7742210_008
 
7742210_008 cylinder block
TD120AHC; TD120ARC; TAD120AHC
7742210_004
 
7742210_004 cylinder head
TD120AHC; TD120ARC; TAD120AHC
7742210_009
 
7742210_009 cylinder block
TD120AHC; TD120ARC; TAD120AHC
7742210_005
 
7742210_005 cylinder head
TD120AHC; TD120ARC; TAD120AHC
Back to top