31336215 Volvo.Penta Cylinder head gasket


31336215 Cylinder head gasket Volvo.Penta D3-110I-D; D3-110I-E; D3-110I-F Cylinder
31336215 Cylinder head gasket Volvo Penta
Rating:
58

Buy Cylinder head gasket 31336215 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 26
 

Compatible models:

Volvo Penta entire parts catalog list:

D3-110I-D; D3-110I-E; D3-110I-F; D3-140I-E; D3-140I-F; D3-140A-D; D3-140A-E; D3-140A-F; D3-150I-D; D3-150I-E; D3-150I-F; D3-170I-D; D3-170I-

Information:


Illustration 1 g00596481
Schematic For Speed Sensor (Engine)Note: This speed sensor is sometimes referred to as a magnetic pickup (MPU).The EMCP II monitors engine speed in order to use the information when the information is needed for other tasks. The following list contains tasks that use the information from the speed sensor:
Activating an engine overspeed shutdown
Terminating engine cranking
Determining the oil step speed
Engaging the air shut off solenoidsThe EMCP II does not control engine speed. The engine speed sensor is mounted on the flywheel housing of the engine. The sensor creates a sine wave signal from passing ring gear teeth at the rate of one pulse per tooth. The sensor sends the GSC a sine wave signal in which the frequency is in direct proportion to the speed of the engine. The GSC treats a CID 190 as a shutdown fault. The engine is not allowed to crank when this diagnostic code is active.Note: Engines that are equipped with a PEEC electronic control module have a separate speed sensor. The cable of the speed sensor that is used by the GSC is marked "838-873", "838-973", or "973-938".Note: Faults are created when the harness connector (40 contact) is disconnected from the GSC during these troubleshooting procedures. Clear these created faults after the particular fault is corrected. In a properly operating system, when the harness connector is removed from the GSC, the following diagnostic codes are recorded:
CID 100 FMI 3 pressure sensor (engine oil)
CID 110 FMI 3 temperature sensor (engine coolant)
CID 111 FMI 3 fluid level sensor (engine coolant)
CID 190 FMI 3 speed sensor (engine)
CID 331 FMI 2 switch (engine control)
CID 336 FMI 2 switch (engine control)ProcedureThe following condition could be the cause of a CID 190 FMI 3:
There is an open circuit of the signal wire.Clear the diagnostic code from the fault log after troubleshooting is complete.
Check the harness and the sensor.
Turn the ECS to OFF/RESET.
Disconnect the harness connector from the GSC.
At the GSC harness connector, measure the resistance from contact 1 to contact 2. Expected Result: The resistance should be 100 to 350 ohm. Results:
OK - The fault is most likely intermittent. Reconnect the harness connector to the GSC. Turn the ECS to OFF/RESET and then turn the ECS to STOP. Verify that a CID 190 remains active on the upper display.
If a CID 190 is showing,


Parts cylinder Volvo Penta:

3801383
 
3801383 Cylinder head
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G
36002661
 
36002661 Cylinder head
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G
3801563
 
3801563 Cylinder head, exch
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G
31392321
 
31392321 Cylinder head gasket
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
31392322
 
31392322 Cylinder head gasket
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
31392323
 
31392323 Cylinder head gasket
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
31392324
 
31392324 Cylinder head gasket
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
31392325
 
31392325 Cylinder head gasket
D3-110I-D; D3-110I-E; D3-110I-F, D3-110I-G; D3-140A-G; D3-140I-G, D3-110I-H; D3-140A-H; D3-140I-H
Back to top