834930 Volvo.Penta Cylinder head


834930 Cylinder head Volvo.Penta AQ190A; AQ240A Cylinder
834930 Cylinder head Volvo Penta
Rating:
78

Buy Cylinder head 834930 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

AQ190A; AQ240A   Volvo.Penta

Volvo Penta entire parts catalog list:

AQ190A; AQ240A

Information:

Bosch Fuel Injection Pump (EPVE)
Illustration 1 g00896561Note: Parts that are inside of the fuel injection pump are only serviceable by an authorized Bosch dealer. Please consult your parts book for availability of parts on the outside of the pump that are not related to the settings of the fuel pump and for the possibility of remanufacturing options.Hub nut (not shown)Note: Do not release the hub nut from the fuel injection pump. The fuel pump hub is positioned to the pump shaft in order to ensure that the fuel pump is in the correct position for timing. If the hub is removed, the hub will need to be accurately positioned to the pump shaft. Accurate positioning requires the use of special equipment by a Caterpillar Dealer. (1) Tighten the screw for the low idle speed adjustment to the following torque. ... 4 to 4.5 N m (35 to 40 lb in) (2) Tighten the fitting for the fuel return line connection to the following torque. ... 5 to 6 N m (44 to 53 lb in) (3) Tighten the fitting for the fuel supply connection to the following torque. ... 22 N m (16 lb ft) (4) Boost control (if equipped) (5) Tighten the high idle speed adjustment screw to the following torque. ... 4 to 4.5 N m (35 to 40 lb in) (6) Tighten the nuts for the high pressure fuel line connection to the following torque. ... 22 N m (16 lb ft) (7) Tighten the flange nuts to the following torque. ... 22 N m (16 lb ft) (8) Tighten the fittings for the fuel discharge lines to the following torque. ... 70.5 to 81.4 N m (52 to 60 lb ft)
Illustration 2 g00766439 (9) Locking spacer (If equipped) Note: The drive shaft of the fuel injection pump must not be turned without the spacer in position under the locking screw (10). (10) Tighten the locking screw to the following torque. ... 27 N m (20 lb ft) (11) Tighten the nut for the drive gear to the following torque. ... 80 N m (59 lb ft)
Illustration 3 g00639086Note: Before the crankshaft is turned or the fuel injection pump is installed, move the locking spacer (9) under the locking screw (10). Refer to position (A) that is in Illustration 3. This position ensures that the pump drive shaft is released.Timing Information for the Bosch Fuel Injection Pump
Table 1
Early Bosch Fuel Injection Pump Without Locking Screw
Code Letters on Fuel Injection Pump Engine Check Angle (degrees)(1) Fuel Injection Pump Mark Angle (degrees)(1) Static Timing Position Before TC Position (degrees) Piston Displacement(1)
"BK" 308 314 12 1.78 mm (0.070 inch)
"CK" 308 314 12 1.78 mm (0.070 inch)
"DK" 306 313 14 2.42 mm (0.095 inch)
"EK" 308.5 315.5 14 2.42 mm (0.095 inch)
"EK"(2) 306.5 315.5 18 3.99 mm (0.157 inch)
"EM" 288.5 295.5 14 2.42 mm (0.095 inch)
"FM" 289 295 12.5 1.93 mm (0.076 inch)
"JM" - - 6 -
"JM"(3) - - 2 -
"JM"(4) - - TDC -
"KC"(5) - - TDC -
"KL"(5) - - TDC -
"ML"(5) - - TDC -
"PM" - - 12 -
"SK" - - 9 -
"TL"(5) - - TDC -
VM - - 2 ATDC -
(1) The engine must be set at the TC position on the compression stroke for the number 1 piston. The fuel injection pump mark angle and the displacement of the piston can be checked when the plunger for the fuel injection pump is set at 1.00 mm (0.039 inch).
(2) The information plate on the fuel injection pump is stamped "J609".
(3) "AD70229" and "AD702230" only
(4) "AD80643" only
(5) The cold start advance (KSB) must be energized before the timing is set.Note: Later Bosch Fuel Injection Pumps use a pin to time the pump.Stanadyne Fuel Injection Pump (DB2 or DB4)


Parts cylinder Volvo Penta:

7742260_005
7742260_003
 
7742260_003 cylinder head
AQ190A; AQ240A
835718
 
835718 Cylinder head
AQ190A; AQ240A
834932
 
834932 Cylinder head
AQ190A; AQ240A
834931
 
834931 Cylinder head
AQ190A; AQ240A
826363
 
826363 Cylinder block
AQ190A; AQ240A
834934
 
834934 Cylinder block
AQ190A; AQ240A
835714
 
835714 Cylinder block
AQ190A; AQ240A
Back to top