875462 Volvo.Penta Cylinder liner kit


875462 Cylinder liner kit Volvo.Penta MD70B; MD70BK; TMD70B Cylinder
875462 Cylinder liner kit Volvo Penta
Rating:
88

Buy Cylinder liner kit 875462 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Volvo Penta entire parts catalog list:

Information:


Table 1
J1939 Code and Description Comments
105-3
Engine Intake Manifold #1 Temperature : Voltage Above Normal The Electronic Control Module (ECM) detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
105-4
Engine Intake Manifold #1 Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
110-3
Engine Coolant Temperature : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
Note: For a 110-3 code, start the engine and let the engine idle for 7 minutes. The engine must be running for at least 7 minutes in order for the diagnostic to run.
110-4
Engine Coolant Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
171-3
Ambient Air Temperature : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
171-4
Ambient Air Temperature : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
175-3
Engine Oil Temperature 1 : Voltage Above Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged.
175-4
Engine Oil Temperature 1 : Voltage Below Normal The ECM detects signal voltage that is not in the acceptable range.
The value of the parameter is set to a default value.
The code is logged. The sensor signal for the passive sensor is routed from the ECM to terminal 1 of the sensor connector. The sensor return for the passive sensors is routed from the ECM to terminal 2 of the sensor connector.When the ECM detects voltage that is above a threshold on the signal wire, the ECM activates a high voltage -3 diagnostic code. When the ECM detects voltage that is below a threshold on the signal wire, the ECM activates a low voltage -4 diagnostic code.Note: There may be a delay of 30 seconds or more in order for Cat® Electronic Technician (ET) to display an active diagnostic code. When you check for a diagnostic code, be sure to wait at least 30 seconds.
Illustration 1 g06406384
For the complete circuit details, refer to the full schematic.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Determine if a code is active or logged.
Codes
Result: A -3 code is active.
Proceed to Test Step 2.
Result: A -4 code is active.
Proceed to Test Step 3.
Result: For a code that is logged, but not currently active.
Proceed to Test Step 4.
2. Create a Short at the Sensor Connector
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the sensor with the active -3 code.
C. Install the jumper wire between the following terminals at the sensor connector:
- Terminal 1 (sensor signal) and Terminal 2 (sensor return)
D. Connect Cat ET.
E. Use Cat ET to monitor the following:
- -4 code
F. Turn the main disconnect switch to the OFF position.
Create a Short
Result: The -3 code remains active.
Repair: There is an open in the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: A -4 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
3. Create an Open at the Sensor Connector
A. Turn the main disconnect switch to the OFF position.
B. Disconnect the sensor with the active -4 code.
C. Connect Cat ET.
D. Use Cat ET to monitor the following:
- -3 code
Note: For a 110-3 code, start the engine and let the engine idle for 7 minutes. The engine must be running for at least 7 minutes in order for the diagnostic to run.
E. Turn the main disconnect switch to the OFF position.
Create an Open
Result: The -4 code remains active.
Repair: There is an open in the wiring harness. Repair or replace the wiring harness.
Verify that the repair eliminated the problem.
Result: A -3 code became active.
Repair: The wiring harness is OK. Replace the sensor.
Verify that the repair eliminated the problem.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).


Parts cylinder Volvo Penta:

275525
 
275525 Cylinder head gasket
AQD70D; TAMD70D; TAMD70E, D70B; D70B PP; D70B K, D70CHC; D70CRC; TD70CHC, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C, TD70G; TD70G-83; TD70GPP
832268
 
832268 Cylinder liner
AQD70D; TAMD70D; TAMD70E, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
471000
Cylinder block
471000 Cylinder block
MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
275039
Cylinder liner kit
275039 Cylinder liner kit
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B
275055
Cylinder liner kit
275055 Cylinder liner kit
MD70B; MD70BK; TMD70B
875541
 
875541 Cylinder liner kit
MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
3803031
 
3803031 Cylinder head
D70B; D70B PP; D70B K, MD70B; MD70BK; TMD70B, MD70C; TMD70C; TAMD70C
471008
Cylinder head
471008 Cylinder head
MD70B; MD70BK; TMD70B
Back to top