1545445 Volvo.Penta Delivery pipe


1545445 Delivery pipe Volvo.Penta TD30A; TD31ACE; TD40A Delivery
1545445 Delivery pipe Volvo Penta
Rating:
93

Buy Delivery pipe 1545445 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$181.00
 

23-05-2023
0.02[0.01] Pounds
-: -
Thicon Models 1545445 50032 1:14, 1:16 Trailer Coupling 1 Piece
Thicon Models 50032 1:14, 1:16 Trailer Coupling 1 Piece || Contents: 1 item
$57.34
 

10-05-2022

-: -
SHAFT FOR HYSTER: 1545445
HYSTER || All Brand new & rebuilt items comes with 1 year warranty. || SHAFT. Category: HYSTER FORKLIFT PARTS. This part can also be found under the following part numbers: HY1545445 1545445  HYSTER 1545445  HYSTER1545445 1545445     . All Brand new & rebuilt items comes with 1 year warranty.
Number on catalog scheme: 44
 

Compatible models:

Volvo Penta entire parts catalog list:

TD30A; TD31ACE; TD40A; TD45B; D45A

Information:


Illustration 1 g01507813 (1) Torque for four bolts ... 108 5 N m (80 4 lb ft) (2) Torque for the bolt ... 58 6 N m (43 4 lb ft)
Illustration 2 g01507808 (3) Measure the amount of the warpage of the cylinder block with a straightedge and feeler gauge. Maximum allowable clearance ... 0.05 mm (0.002 inch)Repair limit ... 0.20 mm (0.008 inch)Resurface the top of the block if the repair limit is reached.
Illustration 3 g01507814 (4) Measure the inside diameter of the cylinder sleeve that is parallel to the crankshaft. Measure the inside diameter of the cylinder liner that is in a perpendicular position to the crankshaft. Measure the top, the middle and the bottom of the cylinder liner. Refer to Table 1 for tolerances of the cylinder liner.
Table 1
Tolerances of Cylinder Sleeves
Standard at Assembly Repair Limit(1) Service Limit(2)
Inside Diameter 102.010 to 102.045 mm (4.0161 to 4.0175 inch) 102.200 mm (4.0236 inch) 102.700 mm (4.0433 inch)
Out of Round 0.010 mm (0.0004 inch) N/A N/A
Taper 0.015 mm (0.0006 inch) N/A N/A
(1) The repair limit is the maximum dimension or the repair limit is the minimum dimension that is specified for a part. Repair a part if the repair limit is reached.
(2) The service limit is the maximum dimension or the service limit is the minimum dimension that is specified for a part. Replace the part if the service limit is reached.Bore the cylinder to the specified oversize dimension if the inside diameter reaches the repair limit but the inside diameter does not reach the service limit. Refer to Table 2.Hone the liner to +0.25 mm (+0.010 inch) or +0.50 mm (+0.020 inch) oversize. Hone the liner to an accuracy within 0.010 to 0.045 mm (0.0004 to 0.0018 inch).Determine the oversize dimension that is necessary in order to clean up the cylinder if any liner has uneven wear.Replace all cylinder liners that are in excess of the service limit.Note: Refinish all liners to the same oversize dimension. Use a ridge reamer in order to cut the ridge of the cylinder if the liner is in good condition. Hone the cylinder bore.
Table 2
Oversize Bore Cylinder Bore Size
0.250 mm (0.0098 inch) 102.260 mm (4.0260 inch)
102.295 mm (4.0274 inch)
0.500 mm (0.0197 inch) 102.510 mm (4.0358 inch)
102.545 mm (4.0372 inch)
Illustration 4 g01507815 (5) Service limit of cylinder liner ... 102.700 mm (4.0433 inch)Note: Replace all cylinder liners that exceed the service limit.Use the following procedure in order to replace the cylinder liners.
Set up a boring machine on the cylinder block. Align the boring machine with the center of the bottom of the cylinder liner with the least worn area.
Bore the liner until the thickness is 0.50 mm (0.020 inch).
Remove the remainder of the liner. Be careful not to damage the cylinder block.
Install a new liner. Align the liner with the top of the cylinder block.
The bore of the cylinder must be 102.000 to 102.035 mm (4.0157 to 4.0171 inch). Diameter for the main bearing bores ... 95.000 mm (3.7402 inch)Maximum diameter of the main bearing bores ... 95.022 mm (3.7410 inch)New height of deck from centerline of crankshaft to deck ... 307.00 0.05 mm (12.086 0.002 inch)Minimum height from the centerline of crankshaft to deck ... 306.70 mm (12.075 inch)


Parts delivery Volvo Penta:

859055
 
859055 Delivery pipe
AD30A; AQAD30A; MD30A, MD31A; TMD31A; TMD31B, TD30A; TD31ACE; TD40A
838442
 
838442 Delivery valve
AD30A; AQAD30A; MD30A, MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A
858098
 
858098 Delivery valve
MD40A; TMD40A; TMD40B, TD30A; TD31ACE; TD40A
1542189
 
1542189 Delivery pipe
TD30A; TD31ACE; TD40A
1542161
 
1542161 Delivery pipe
TD30A; TD31ACE; TD40A
1545441
 
1545441 Delivery pipe
TD30A; TD31ACE; TD40A
1542162
 
1542162 Delivery pipe
TD30A; TD31ACE; TD40A
4804750
 
4804750 Delivery pipe
TD30A; TD31ACE; TD40A
Back to top