241531 Volvo.Penta Distributor


241531 Distributor Volvo.Penta AQ115A; AQ115B; AQ130 Distributor
241531 Distributor Volvo Penta
Rating:
23

Buy Distributor 241531 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$88.88
 

10-07-2022

-: -
Duck MAX Strength Packing Tape Refill, 8 Rolls, 1.88 Inch x 54.6 Yard, Clear (241531)
Great for heavy duty moving and shipping || 100x stronger than acrylic tapes based on ASTM D3654B for maximum hold on boxes || This 3.1 mil tape is the strongest Duck Brand packing tape, designed for sealing the heaviest packages || Made with hot melt adhesive for an instant, quick stick to corrugate || Meets postal regulations for shipping tape
$429.03
 

09-08-2021

-: -
Duck MAX Strength Packing Tape Refill, 8 Rolls, 1.88 Inch x 54.6 Yard, Clear (241531), Pack of 5
Great for heavy duty moving and shipping || 100x stronger than acrylic tapes based on ASTM D3654B for maximum hold on boxes || This 3.1 mil tape is the strongest Duck Brand packing tape, designed for sealing the heaviest packages || Made with hot melt adhesive for an instant, quick stick to corrugate || Meets postal regulations for shipping tape
Number on catalog scheme: 8
 

Compatible models:

Volvo Penta entire parts catalog list:

AQ115A; AQ115B; AQ130; AQ130A; AQ130B; AQ130C; AQ130D; AQ165A; AQ170A; AQ170B; AQ170C; AQD21A; BB115A; BB115B; BB115C; BB165A; BB170A; BB170B; BB1

Information:

2. Loosen three clamps (3) and remove tubes (4) and (5). 3. Remove the nuts and bracket (6) if the exhaust manifold on the right side of the machine is to be removed.4. Remove the nuts, spacers and exhaust manifold (7) from the engine. 5. Remove gaskets (8). 6. Make a separation of manifolds (9), (10) and (11).Install Exhaust Manifold
Make sure the 2P2333 Manifold Sealer does not get on the inside of each manifold. Damage to the turbocharger could be the result if the manifold sealer gets on the impeller on the turbocharger.
1. Put 2P2333 Manifold Sealer on surfaces (X) on the manifolds.2. Make a connection of manifolds (1), (2) and (3). 3. Put 5P3931 Anti-Seize Compound on the threads of studs (5). Put gaskets (4) in position on the studs. 4. Install exhaust manifold (6) or the engine. Install the spacers and nuts that hold the exhaust manifold in place. Tighten the nuts finger tight only. If the right exhaust manifold was removed, install the bracket that gives support to the shield on the end of the exhaust manifold. 5. On 3412 Generator Sets, use the sequence above to tighten the nuts to a torque of 52 7 N m (38 5 lb.ft.). 6. On 3408 Generator Sets, use the sequence above to tighten the nuts to a torque of 52 7 N m (38 5 lb.ft.). 7. Put seal (8) in position on tube (9). Install tube (9) in tube (7). Install tube (7) and tube (9) on the engine. Install the clamps on tube (8) and tube (7). 8. Install clamp (10). Install the clamp so that the bolt in the clamp is 15° 10° up from vertical as shown. Put 5P3931 Anti-Seize Compound on the threads of the bolts that hold shield (11) in place. Install shield (11). Exhaust manifolds on the left side of the engines do not have shield (11). 9. For exhaust manifolds on the left side of the machine, install clamp (12) so that the bolt in the clamp is 45° 10° down from a horizontal line as shown.10. Install support (13). 11. Install breather tube (14). Install the bolt that holds clip (15) to the bonnet.Remove Exhaust Manifold (Watercooled)
1. Drain the cooling system to a level below that of the exhaust manifold.2. Remove bolts (1) and the two bolts behind the fuel filter. Move bracket assembly (2) away from the exhaust manifold. Do Steps 3 and 4 if the watercooled exhaust manifold on the left side (as seen from the generator end) is to be removed.3. Remove nuts, washers and bolts (3) that hold the two braces to the air cleaner housing. Loosen clamp (4). 4. Fasten tool (A) and a hoist to the air cleaner housing. Remove bolts (5) and the washers that hold air cleaner housing support (6) in position. Remove air cleaner housing and support (6) from the machine as a unit. 5. Remove nuts (7), the bolts and washers that hold elbow (9) in place. Remove elbow (9) and the gaskets.6. Remove nuts (8) and the bolts. 7. Remove elbow (10) and the gasket from the front of the manifold. 8. Remove the nuts, washers and spacers (11). Remove watercooled exhaust manifold (12) and gasket (13).9. On 3412 Generator Sets that have a watercooled exhaust manifold, use a hoist to remove the exhaust manifold. Weight is approximately 27 kg (60 lb.).10. Remove the gasket that is between the exhaust manifold and the cylinder head.


Parts distributor Volvo Penta:

834465
 
834465 Distributor
AQ115A; AQ115B; AQ130
834466
 
834466 Distributor
AQ115A; AQ115B; AQ130
243632
 
243632 Distributor cap
AQ115A; AQ115B; AQ130
243797
Distributor cap
243797 Distributor cap
AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ145A; BB145A
243796
Distributor arm
243796 Distributor arm
AQ115A; AQ115B; AQ130
241669
Distributor cap
241669 Distributor cap
AQ115A; AQ115B; AQ130
243657
Distributor arm
243657 Distributor arm
AQ115A; AQ115B; AQ130
243803
 
243803 Distributor cap
AQ115A; AQ115B; AQ130
Back to top