22492124 Volvo.Penta Drive unit


22492124 Drive unit Volvo.Penta SX-A; DPS-A; DPS-B Drive
22492124 Drive unit Volvo Penta
Rating:
13

Buy Drive unit 22492124 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

SX-A; DPS-A; DPS-B   Volvo.Penta

Volvo Penta entire parts catalog list:

SX-A; DPS-A; DPS-B; DPS-B1; DPS-A OXi; DPS-B OX; DPS-B1 OX; FWD; SX-A 1.43; SX-A 1.51; SX-A 1.60; SX-A 1.66; SX-A 1.79; SX-A 1.89; SX-A 1.97; S

Information:

Initial Inspection
Perform the required daily maintenance and other periodic maintenance before you start the engine. Inspect the engine compartment. This inspection can help prevent major repairs at a later date. Refer to the Operation and Maintenance Manual, "Walk-Around Inspection" topic (Maintenance Section) for more information.
For the maximum service life of the engine, make a thorough inspection before you start the engine. Look for the following items: oil leaks, coolant leaks, loose bolts and trash buildup. Remove trash buildup and arrange for repairs, as needed.
Inspect the cooling system hoses for cracks and for loose clamps.
Inspect the alternator and accessory drive belts for cracks, breaks, and other damage.
Inspect the wiring for loose connections and for worn wires or frayed wires.
Check the fuel supply. Drain water from the water separator (if equipped). Open the fuel supply valve.
All valves in the fuel return line must be open before and during engine operation to help prevent high fuel pressure. High fuel pressure may cause filter housing failure or other damage.
Do not start the engine or do not move any of the controls if there is a "DO NOT OPERATE" warning tag or similar warning tag attached to the start switch or to the controls.
Ensure that the areas around the rotating parts are clear.
All of the guards must be put in place. Check for damaged guards or for missing guards. Repair any damaged guards. Replace damaged guards and/or missing guards.
Disconnect any battery chargers that are not protected against the high current drain that is created when the electric starting motor (if equipped) is engaged. Check electrical cables and check the battery for poor connections and for corrosion.
Reset all of the shutoffs or alarm components.
Check the engine lubrication oil level. Maintain the oil level between the "ADD" mark and the "FULL" mark on the oil level gauge.
Check the coolant level. Observe the coolant level in the coolant recovery tank (if equipped). Maintain the coolant level to the "FULL" mark on the coolant recovery tank.
If the engine is not equipped with a coolant recovery tank maintain the coolant level within 13 mm (.5 inch) of the bottom of the filler pipe. If the engine is equipped with a sight glass, maintain the coolant level in the sight glass.
Observe the air cleaner service indicator (if equipped). Service the air cleaner when the yellow diaphragm enters the red zone, or when the red piston locks in the visible position.
Ensure that any driven equipment has been disengaged. Remove any electrical loads.Cold Weather Starting
Starting the engine and operation in cold weather is dependent on the type of fuel that is used, the oil viscosity, and other optional starting aids. For more information, refer to the Operation and Maintenance Manual, "Cold Weather Operation" topic (Operation Section).Air Inlet Heater
DO NOT USE ETHER (starting fluids) unless specifically instructed to do so. If the engine is equipped with an Air Inlet Heater (electrically or fuel ignited manifold heater), DO NOT use ether (starting fluids) at any time. The use could result in engine damage and/or personal injury.
Note: There will be an indicator lamp on the control panel that is marked "AIR INLET HEATER".For detailed information on the operation of the Air Inlet Heater, refer to Testing and Adjusting, "Air Inlet and Exhaust System - Inspect".Refer to the Owner's Manual of the OEM for your type of controls. Use the following procedure to start the engine.
Place the transmission in NEUTRAL. Disengage the flywheel clutch in order to allow the engine to start faster. This also reduces the draining of the battery.
Turn the ignition switch to the ON position.The " and DIAGNOSTIC" lamp (if equipped) will flash while the engine is cranking. The lamp should turn off after proper engine oil pressure is achieved. If the lamp fails to flash, notify your authorized Caterpillar dealer. If the lamp continues to flash, the Electronic Control Module (ECM) has detected a problem in the system. For more information, refer to the Operation and Maintenance Manual, "Diagnostic Flash Code Retrieval" (Operation Section).
Do not engage the starting motor when flywheel is turning. Do not start the engine under load.If the engine fails to start within 30 seconds, release the starter switch or button and wait two minutes to allow the starting motor to cool before attempting to start the engine again.
Push the start button or turn the ignition switch to the START position in order to crank the engine.Do not push down or hold the throttle down while the engine is cranked. The system will automatically provide the correct amount of fuel that is needed to start the engine.
If the engine fails to start within 30 seconds, release the start button, or the ignition switch. Wait for two minutes in order to allow the starting motor to cool before attempting to start the engine again.Note: The " and DIAGNOSTIC" lamps (if equipped) may come on after the engine is started. If this occurs, the ECM has detected a problem with the system. For more information, refer to the Operation and Maintenance Manual, "Diagnostic Flash Code Retrieval" (Operation Section) .
Oil pressure should rise within 15 seconds after the engine starts. Do not increase engine rpm until the oil pressure gauge indicates normal. If oil pressure is not indicated on the gauge within 15 seconds, DO NOT operate the engine. STOP the engine, investigate and correct the cause.
Allow the engine to idle for approximately three minutes. Idle the engine until the water temperature gauge has begun to rise. Check all gauges during the warm-up period.Note: Oil pressures and fuel pressures should be in the normal range on the instrument panel. Engines that are equipped with "" lamps do not have an operating range. The " and DIAGNOSTIC" lamp (if equipped) will flash while the engine is cranking. The lamp should turn off after proper engine oil pressure or fuel pressure is achieved. Do not apply a load to the engine or increase engine rpm until the oil pressure gauge indicates at least normal pressure. Inspect the engine for leaks and/or unusual noises.


Parts drive Volvo Penta:

3883600
 
3883600 Drive unit, SX-A
SX-A; DPS-A; DPS-B
3883601
 
3883601 Drive unit, SX-A
SX-A; DPS-A; DPS-B
3883602
 
3883602 Drive unit, SX-A
SX-A; DPS-A; DPS-B
21615545
 
21615545 Drive unit
SX-A; DPS-A; DPS-B
22104467
 
22104467 Drive unit
SX-A; DPS-A; DPS-B
22104410
 
22104410 Drive unit
SX-A; DPS-A; DPS-B
22777846
 
22777846 Drive unit
SX-A; DPS-A; DPS-B
22861607
 
22861607 Drive unit
SX-A; DPS-A; DPS-B
Back to top