3868394 Volvo.Penta Drive


3868394 Drive Volvo.Penta SX-C; SX-C1; SX-C2 Drive
3868394 Drive Volvo Penta
Rating:
53

Buy Drive 3868394 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

SX-C; SX-C1; SX-C2   Volvo.Penta

Volvo Penta entire parts catalog list:

SX-C; SX-C1; SX-C2; SX-CT; SX-CT1; SX-R; SX-RT1; SX-RT2; DP-S; DP-S1; SX-C1AC; TSK SX-C1; TSK SX-C1AC; TSK DP-S; TSK SX-C; SX-CT2; TSK SX-C2AC; T

Information:


Illustration 1 g01065745
Right side view
(1) 6V-3093 Transducer Adapter
(2) 6V-2197 Magnetic Transducer
(3) Connector for the 7X-1695 cable
(4) 7X-1695 Cable
Set the engine control to the OFF/RESET mode. Remove the timing calibration plug from either the left side or the right side of the flywheel housing. Install 6V-3093 Transducer Adapter (1) into the hole.
The timing hole in the flywheel must not be aligned with the hole for the transducer. The transducer will be damaged on engine start-up if the transducer is installed through both holes. Rotate the flywheel for more than 10 degrees before or after the TC position in order to move the flywheel hole away from the hole for the transducer. Always confirm that the holes are not aligned.
Make sure that the hole in the flywheel housing for the transducer is not aligned with the timing hole in the flywheel. Remove the protective end cap from 6V-2197 Transducer (2). Insert the transducer into the adapter until the transducer contacts the surface of the flywheel. Move the transducer 1 mm (0.04 inch) away from the surface of the flywheel. Tighten the nut on the adapter in order to secure the transducer in place.
Connect the one end of 7X-1695 Cable As (4) to the transducer. Connect the other end of the cable to connector (3) on the side of the engine.
Connect Cat ET to the service tool connector on the terminal box. For instructions, refer to Troubleshooting, "Electronic Service Tools". Start Cat ET.
Calibration Note: A two-step process is used to calibrate the signal for the speed/timing sensor. The new timing reference is calculated first. The reference is based on the signals from the transducer and the speed/timing sensor. Next, the new timing reference is programmed into the permanent memory of the ECM.
Start the engine. Operate the engine at the rated speed and load.
Select "Service" from the main menu on Cat ET. Select "Calibrations" from the menu. Select "Timing Calibration".
Use either of the following methods in order to initiate the calculation of the new timing reference:
Press the space bar on the keyboard of the PC.
Click the left mouse button on the "Continue" button in the lower left corner of the Cat ET screen.Cat ET will indicate "Please wait...Calculating the new Timing Reference". After a few moments, Cat ET will display "The ECM has calculated the Timing Reference" and "Choose the Continue button to program the Timing Reference".
Use either of the following methods in order to program the new timing reference:
Press the space bar on the keyboard of the PC.
Click the left mouse button on the "Continue" button in the lower left corner of the Cat ET screen.Successful CalibrationAfter a few moments, Cat ET displays "CALIBRATION SUCCESSFUL".Disconnect the transducer and the cable. Remove the adapter and reinstall the timing calibration plug. Replace the protective cover on the transducer. The calibration is complete.Unsuccessful CalibrationAfter a few moments, Cat ET displays "COULD NOT CALIBRATE". Verify that the engine rpm was stable during the calibration ( 50 rpm). Verify that there are no active diagnostic codes which can prevent the calibration. Repeat the calibration procedure.If the calibration is still unsuccessful, check the installation of the tools and the operation of the tools. Check the 7X-1695 Cable As for continuity. Verify that the transducer is not bent, open, or shorted internally. Repeat the calibration procedure.Excessive backlash in the gear train will cause inconsistent timing. Refer to Disassembly and Assembly for identifying and repairing a gear train problem.


Parts drive Volvo Penta:

3868286
 
3868286 Drive
SX-C; SX-C1; SX-C2
3868392
 
3868392 Drive
SX-C; SX-C1; SX-C2
3868393
 
3868393 Drive
SX-C; SX-C1; SX-C2
3868586
 
3868586 Drive
SX-C; SX-C1; SX-C2
3868816
 
3868816 Drive
SX-C; SX-C1; SX-C2
3868587
 
3868587 Drive
SX-C; SX-C1; SX-C2
3852404
 
3852404 Drive gear set
SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST
3852403
 
3852403 Drive gear set
SX-C; SX-C1; SX-C2, SX-M1; SX-M1 1.43; SX-M1 1.51, SX-M; SX-MTD; SX-MTD3, SX-S; SX-SLT; SX-ST
Back to top