821045 Volvo.Penta Electrical distribut


821045 Electrical distribut Volvo.Penta D100A; D100AK; D100B, D120A; D120AK; TD120A, D70B; D70B PP; D70B K, MD100A; TMD100A; TMD100AK, TID120FPP; TID120FG; TD120G Electrical
821045 Electrical distribut Volvo Penta
Rating:
38

Buy Electrical distribut 821045 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$455.58
 

21-04-2024
13.7347[6.18] pounds
LU: Amazon Global Store
Valeo 821045 Clutch Sets
Valeo Diameter 1 [mm]: 215 || Diameter 2 [mm]: 215 || New Part: || Number of teeth: 14 || Supplementary Article/Info 2: with releaser
$8.99
 

29-04-2020
5.6[2.25] Pounds
-: -
Mercury Marine/Mercruiser New OEM SCREW 10-4009340; 10-82104540; 821045 40
SKU: 10-4009340 || Sold Each || Please verify your own fitment
$20.40
 

21-04-2024
0.02[0.01] pounds
US: Advance Cycle Parts
Red Horse Performance 821-04-5-04 Male 90 Degree AN/JIC Flare Adapter - Clear
Red Horse Performance Red Horse Performance 821-04-5 -04 Male 90 Degree AN/JIC Flare Adapter - Clear
Number on catalog scheme: 1
 

Information:


Table 1
Diagnostic Trouble Codes for DEF Module Does Not Respond
J1939 Code Description Notes
5394-7 Aftertreatment Diesel Exhaust Fluid Dosing Valve : Not Responding Properly The Electronic Control Module (ECM) detects that the DEF injector does not open when requested.
The battery voltage is at least 10 V.
There are no other active diagnostic codes for the DEF injector.
The warning lamp will flash. The engine will be derated.
Follow the troubleshooting procedure in order to identify the root cause of the problem. Note: The procedures have been listed in order of probability. Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for Active Diagnostic Codes
A. Connect the electronic service tool to the diagnostic connector.
B. Turn the keyswitch to the ON position.
C. Use the electronic service tool to check for active diagnostic codes.
Diagnostic codes
Result: There are other active diagnostic codes relating to the DEF injector or the DEF quality.
Repair: Troubleshoot the other diagnostic codes before returning to this procedure. Refer to Troubleshooting, "Diagnostic Trouble Codes".
Result: There are no other active diagnostic codes relating to the DEF injector or the DEF quality. A 5394-7 diagnostic code is active.
Proceed to Test Step 2.
2. Perform the "DEF Dosing System Accuracy Test"
Note: The DEF Dosing System Accuracy Test must be performed twice. The first attempt is to dissolve DEF deposits that may have formed around the injector tip. The second attempt is the test for amount dosed.
A. Perform the "DEF Dosing System Accuracy Test". Refer to Systems Operation, Testing and Adjusting, "Aftertreatment SCR System Dosing Test" for the correct procedure.
DEF dosing
Result: The quantity of DEF collected on the second test is not within the acceptable range.
Proceed to Test Step 3.
Result: The quantity collected is within the desired range.
Proceed to Test Step 4.
3. Check the DEF Pressure Line
A. Turn the keyswitch to the OFF position for 2 minutes.
B. Visually inspect the lines for leaks or damage.
C. Remove the DEF pressure line between the DEF pump and the DEF injector. Refer to the Disassembly and Assembly, "Diesel Exhaust Fluid Lines - Remove and Install".
D. Check for ice, urea deposits, or debris in the DEF pressure line.
Pressure line
Result: There is ice in the pressure line.
Repair: Check the operation of the line heaters. Refer to Troubleshooting, "DEF Line Heater - Test".
Result: There are restrictions or leaks in the lines.
Repair: Remove the restrictions or replace the pressure line.
Result: There are no restrictions in the lines.
Repair: Replace the DEF injector. Refer to Disassembly and Assembly, "DEF Injector and Mounting - Remove and Install".
4. Check that the Fault has Cleared
A. Reconnect the DEF lines. Reinstall the DEF injector.
B. Connect to the electronic service tool.
C. Operate the engine at a high speed and load point until the SCR inlet temperature is greater than 200° C (392° F) and the DEF system starts dosing operation.
D. Use the electronic service tool to check for active diagnostic codes.
Diagnostic codes
Result: The diagnostic code remains active during dosing operation.
Contact the Dealer Solutions Network (DSN).
Result: The diagnostic code is no longer active and now logged.
Clear all logged diagnostic codes and return the engine to service.


Parts electrical Volvo Penta:

7742200_021
 
7742200_021 ELECTRICAL OIL PUMP
TID120FPP; TID120FG; TD120G
Back to top