3858888 Volvo.Penta Engine control unit


3858888 Engine control unit Volvo.Penta 5.0GLPEFS; 5.0GiPEFS; 5.7GSPEFS, 5.0GLPWTR; 5.0GiPWTR; 5.7GSIPWTR, 5.0GXi-A; 5.7Gi-A; 5.7GXi-A Engine
3858888 Engine control unit Volvo Penta
Rating:
24

Buy Engine control unit 3858888 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 44
 

Volvo Penta entire parts catalog list:

5.0GLPEFS; 5.0GiPEFS; 5.7GSPEFS; 5.7GSIPEFS
5.0GLPWTR; 5.0GiPWTR; 5.7GSIPWTR; 5.7GSPWTR; 5.7GSiPWTRCE
5.0GXi-A; 5.7Gi-A; 5.7GXi-A; 5.7GXi-B; 5.7GiI-A; 5.7GSiI-A; 5.7GXiI-A; 5.7GXiI-B

Information:

Probable Causes
Active codes and logged codes
Electrical connections
Unstable fuel supply
Switches
Circuit protection
Engine speed/timing
Table 1
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
3719-0 E995 (3)
3719-16 E995 (2)
5246-0 E1389 (3) Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 2
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Certain diagnostic codes and/or event codes may cause an engine shutdown. Connect the electronic service tool and check for active codes and for logged codes.
B. Use the electronic service tool to check for associated diagnostic trouble codes. Refer to Table 1
Codes
Result: There are associated diagnostic trouble codes active or logged.
Repair: Troubleshoot any active or logged associated diagnostic trouble codes before continuing with this procedure.
Result: There are no associated diagnostic trouble codes active or logged.
Proceed to Test Step 2.
2. Electrical Connections
A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors.
Connectors
Result: There are suspect connectors.
Repair: Perform the "Wiggle Test" on the electronic service tool.
Repair or replace connectors that are suspect.
Result: There are no suspect connectors.
Proceed to Test Step 3.
3. Electrical Connections
A. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".
Electrical Connectors
Result: The electrical connections are OK.
Proceed to Test Step 4.
Result: The electrical connections are not OK.
Repair: Repair or replace the damaged connectors. Verify that the repair eliminated the fault.
4. Unstable Fuel Supply
A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Note: Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual, "Cold Weather Operation" for further information.
B. Check fuel quality. Check the fuel tank for debris or foreign objects which may block the fuel supply.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 5.
Result: The fuel quality is not OK.
Repair: Replace the fuel. Verify that the repair eliminated the fault.
5. Switches
A. Check the keyswitch input to the ECM.
B. Check any engine shutdown switches and associated wiring.
Switches
Result: The shutdown switches and wiring are OK.
Proceed to Test Step 6.
Result: The shutdown switches and wiring are not OK.
Repair: Make the necessary repairs, Verify that the repair eliminated the fault.
6. Circuit Protection
A. Inspect the wires and connectors to all circuit protection for the engine.
B. Check the device for circuit protection.
Circuit protection
Result The circuit protection device is tripped.
Repair: Reset the circuit breakers if the circuit breakers are tripped. If necessary, replace blown fuses. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip or the fuse to blow. Make the necessary repairs.
Result The circuit protection device is OK.
Proceed to Test Step 7.
8. Engine Speed/Timing Sensors
A. Inspect the connectors for the engine speed/timing sensors.
B. Crank the engine. If the engine starts and no speed timing codes are logged, the speed timing circuit is operating correctly.
Speed/Timing
Result: The Speed/Timing sensor circuit is not operating correctly.
Repair: Test the speed/timing circuit. Refer to Troubleshooting, "Speed/Timing - Test". Verify that the repair eliminated the fault.
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts engine Volvo Penta:

3862057
 
3862057 Engine
5.0GL-F; 5.0GL-FF, 5.0GL-H; 5.0GL-HF, 5.0GL-J; 5.0GL-JF, 5.0GXi-A; 5.7Gi-A; 5.7GXi-A, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.0GXi-C; 5.0GXi-CF; 5.0GXi-D, 5.0GXi-E; 5.0GXi-EF; 5.0OSi-E, 5.0GXi-F; 5.0GXi-FF; 5.0OSi-F, 5.0GXi-G; 5.0GXi-GF; 5.0OSi-G, 5.0GXi-J;
3858887
 
3858887 Engine control unit
5.0GLPEFS; 5.0GiPEFS; 5.7GSPEFS, 5.0GXi-A; 5.7Gi-A; 5.7GXi-A
3858863
 
3858863 Engine control unit
5.0GLPWTR; 5.0GiPWTR; 5.7GSIPWTR
3858534
 
3858534 Engine anchorage
5.0GXi-A; 5.7Gi-A; 5.7GXi-A, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.7Gi-C; 5.7Gi-CF; 5.7Gi-D, 5.7Gi-E; 5.7Gi-EF; 5.7GiI-E, 5.7GiI-F; 5.7GXiI-G, 5.7GiI-G; 5.7GXiI-H, 8.1Gi-A; 8.1Gi-B; 8.1Gi-BF, 8.1Gi-E; 8.1Gi-EF; 8.1GXi-D, 8.1Gi-F; 8.1Gi-FF; 8.1GXi-E, 8.1Gi
3858473
 
3858473 Engine anchorage
5.0GXi-A; 5.7Gi-A; 5.7GXi-A, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.7Gi-C; 5.7Gi-CF; 5.7Gi-D, 5.7Gi-E; 5.7Gi-EF; 5.7GiI-E, 8.1Gi-A; 8.1Gi-B; 8.1Gi-BF, 8.1Gi-E; 8.1Gi-EF; 8.1GXi-D
3861525
 
3861525 Engine control unit
5.0GXi-A; 5.7Gi-A; 5.7GXi-A
3861215
 
3861215 Engine control unit
5.0GXi-A; 5.7Gi-A; 5.7GXi-A
3862058
 
3862058 Engine
5.0GXi-A; 5.7Gi-A; 5.7GXi-A, 5.0GXi-B; 5.0GXi-BF; 5.0OSi-B, 5.7Gi-300-J; 5.7Gi-300-JF; 5.7OSi-300-J, 5.7Gi-C; 5.7Gi-CF; 5.7Gi-D, 5.7Gi-E; 5.7Gi-EF; 5.7GiI-E, 5.7Gi-F; 5.7Gi-FF; 5.7GXi-G, 5.7Gi-G; 5.7Gi-GF; 5.7GXi-H, 5.7GiC-300-J; 5.7GiC-300-JF; 5.7GX
Back to top