862883 Volvo.Penta Enlargement sleeve


862883 Enlargement sleeve Volvo.Penta TAMD162A; TAMD162B; TAMD162C Enlargement
862883 Enlargement sleeve Volvo Penta
Rating:
103

Buy Enlargement sleeve 862883 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 28
 

Compatible models:

Volvo Penta entire parts catalog list:

TAMD162A; TAMD162B; TAMD162C; TAMD162C-B

Information:


Typical Example1. Remove bolts (1), and pull governor drive (2) from the front drive housing.
Typical Example2. Make sure the O-ring seals are in position on the front of governor drive (1), and put clean engine oil on the seals.3. Put governor drive (1) in position, and install bolts (2) to hold it to the front drive housing.End By:a. install governorDisassemble Governor Drive
Start By:a. remove governor drive 1. Remove O-ring seals (1), (2) and (3) from the front of the governor drive housing.2. Remove the bolts that hold adapter (4) in position, and pull adapter (4) from the housing. 3. Remove pinion (5), shims (6), seals (7) and (8) from adapter (4). Measure the thickness of shims (6), and put identification marks on them for assembly purposes. 4. Remove hose assembly (9)(not included on later machines), cover (11) and the gasket from governor drive housing (10). 5. Remove gear (13) and coupling (12) from housing (10) as a unit. 6. Remove ring (14) to remove coupling (12) from gear (13). 7. If necessary, remove bearing (15) from housing (10).Assemble Governor Drive
1. Align the oil hole in the bearing with the drilled oil passage in governor drive housing (1). Use tool group (A), and install the bearing in housing (1) until it is 1.0 0.5 mm (0.40 .02 in.) below the surface of the housing. The inside diameter of the bearing after assembly is 34.072 0.039 mm (1.3414 .0015 in.). 2. Put coupling (3) in position in gear (2), and install ring (4) to hold the gear and coupling as a unit. 3. Install coupling (3) and gear (2) as a unit in housing (1). 4. Install pinion (5) in adapter (6). 5. Put adapter (6) and shims (7) of the original thickness in position, and install the bolts to hold the unit together.6. Make an adjustment of the gear clearance (backlash) between gear (2) and the pinion as follows:a. Install tool group (B) on gear (2) as shown to check the gear clearance (backlash) at four locations around gear (2) 90° apart.b. Hold the pinion in position, and push down while gear (2) is moved back and forth. Make a record of the indications on tool group (B). Use the lowest indication as the correct gear clearance (backlash) value. The correct gear clearance (backlash) is 0.100 + 0.050 or - 0.025 mm (.0039 + .0020 or - .0010 in.).c. Add or subtract shims (7) as necessary until the gear clearance (backlash) is correct.7. Remove tool group (B), the adapter and pinion from the housing. 8. Connect hose assembly (8) (if equipped) to housing (1). Put the gasket and cover (9) in position, and install the bolts and washers to hold them to housing (1). 9. Install seals (10) and (11) on adapter (6), and put clean engine oil on them.10. Install the correct amount of shims (7) and adapter (6) with the pinion in housing (1), and tighten the bolts. 11. If necessary, make a replacement of pins (14). Make sure the pins are 14 1 mm (.55 .04 in.) above the surface of the housing.12. Install O-ring seal (12) and seals (13) on the front of the housing. Put clean engine oil on the seals.End By:a. install governor drive


Parts enlargement Volvo Penta:

862882
 
862882 Enlargement sleeve
TAMD162A; TAMD162B; TAMD162C, TAMD162C-C; TAMD163A-A; TAMD163P-A, TAMD165A; TAMD165C; TAMD165P
Back to top