3852347 Volvo.Penta Exhaust manifold, exhaust

Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
17-5 Fuel Shutoff Valve : Current Below Normal     The Electronic Control Module (ECM) detects a low current in the circuit for the GSOV for 5 seconds.
The output driver must be off for 5 seconds in order for this code to become active.     The code is logged.
The alarm output is activated.    
17-6 Fuel Shutoff Valve : Current Above Normal     While the output driver is on for 5 seconds, the ECM detected a high current in the circuit for the GSOV for one second.     The code is logged.
The alarm output is activated.
The output driver automatically resets and the output driver continues to try to activate the circuit component.    
17-12 Fuel Shutoff Valve : Failure     The Engine Control Switch (ECS) is placed in the STOP position. The ECM has shut off the fuel to the engine, but the engine rpm does not drop at the expected rate. The deceleration rate must be within rpm of the programmed "Engine Speed Drop Time".     The code is logged.
The alarm output is activated.
The power to the fuel control solenoid remains in the de-energized state and the ECM removes ignition power from the engine.    The ECM contains the logic and the outputs for control of starting the engine and stopping the engine. Some of the logic for starting the engine and for stopping the engine is customer programmable. The logic responds to inputs from the following components: engine control switch, emergency stop switch, remote start switch, data link and other inputs.The ECM outputs a signal to the fuel control solenoid in order to control the fuel shutoff valve. To enable gas flow to the engine, the fuel control solenoid must be energized. The fuel control solenoid may be controlled by the ECM or by the customer equipment. Use this procedure to troubleshoot either configuration.The most likely cause of a diagnostic code is a poor electrical connection or a problem in a wiring harness. The next likely cause may be a problem with the fuel control solenoid. The least likely cause is a problem with the ECM.When the 17-12 Fuel Shutoff Valve failure occurs, the ECM assumes that the fuel shutoff valve did not close. The ECM terminates the ignition. If the fuel control solenoid does not respond to the command, unburned gas will remain in the inlet and exhaust system.Note: Ensure that the unburned gas is purged from the exhaust before restarting the engine. Failure to purge the unburned gas from the engine may result in an explosion in the exhaust piping.The following information describes the systems operation when the GSOV is controlled by the ECM:The ECM sends an output signal to the solenoid for the fuel control valve that controls the operation of the fuel control valve. This output is energize-to-run. During the crank cycle, when the engine speed exceeds 50 rpm, the ECM initiates a +Battery signal to the output for the fuel control valve. The solenoid becomes energized. As the valve opens, fuel begins to flow to the engine. The ECM removes the voltage from this output in order to stop the engine. The solenoid for the fuel control valve becomes de-energized. The fuel flow to the engine is stopped.
Illustration 1 g01752457
Schematic of the configurations for fuel control solenoid by the ECMTest Step 1. Inspect the Electrical Connectors and the Wiring
Set the engine control switch to the OFF/RESET position. Remove the electrical power from the engine.
Illustration 2 g01756053
Location of the connectors at the ECM junction box that are for control of the fuel shutoff valve (left front engine view) (1) J2/P2 ECM connectors for the fuel control solenoid (2) Power harness connectors for the fuel control solenoid
Illustration 3 g01756114
Location of the connectors at the engine junction box that are for control of the fuel shutoff valve (left rear engine view) (3) Power harness connectors at the engine junction box for the fuel control solenoid (4) Emergency stop switch (5) Interconnect harness connectors at the engine junction box for the fuel control solenoid
Illustration 4 g01756093
Location of the components that are for control of the fuel shutoff valve (6) Fuel control solenoid (7) Fuel control valve
Thoroughly inspect connectors (1) , (2) , (3) , and (5) . Also, check the condition of the connectors for emergency stop switch (4) and fuel control solenoid (6) that is for fuel shutoff valve (7) . Refer to Troubleshooting, "Electrical Connectors - Inspect" for details.
Illustration 5 g01415749
Terminal locations at the P2 ECM connector that are associated with the fuel control solenoid (P2-11) Fuel control solenoid (P2-21) Return
Illustration 6 g01756674
Terminal locations for the power harness connector at the ECM junction box that are for the fuel control solenoid (Terminal G) Fuel control solenoid (Terminal F) Return
Illustration 7 g01756653
Terminal locations for the power harness connector at the ECM junction box that are for the fuel control solenoid (Terminal U) Fuel control solenoid (inlet connection) (Terminal V) Return (inlet connection) (Terminal Y) Fuel control solenoid (outlet connection) (Terminal X) Return (outlet connection)