7745660_024 Volvo.Penta exhaust manifold


7745660_024 exhaust manifold Volvo.Penta 740A; BB740A exhaust
7745660_024 exhaust manifold Volvo Penta
Rating:
93

Buy exhaust manifold 7745660_024 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 61
 

Compatible models:

740A; BB740A   Volvo.Penta

Volvo Penta entire parts catalog list:

740A; BB740A

Information:

1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 6-119.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.6. Install the valve covers. See Install Valve Covers. 7. Install plate (4).8. Connect the water line to the air compressor.9. Install bolts (5) for the alternator bracket.END BY:a. install exhaust manifoldb. install fuel injection linesc. install aftercooler housingd. install water temperature regulator


Parts exhaust Volvo Penta:

843235
Exhaust pipe
843235 Exhaust pipe
230A; 230B; 250A, 430; 430A; 430B, 740A; BB740A, AD30A; AQAD30A; MD30A, AQ115A; AQ115B; AQ130, AQ175A, AQ200C; AQ200D; AQ225C, AQ200D; AQ200F; 280B, AQ225D; AQ225E; AQ225F, AQ231A; AQ231B; AQ231LB, AQ260A; AQ260B; BB260A, AQ271A; AQ271B; AQ271C, AQ29
856904
 
856904 Exhaust manifold
430; 430A; 430B, 740A; BB740A
856910
Exhaust riser
856910 Exhaust riser
430; 430A; 430B, 740A; BB740A
856911
Exhaust outlet
856911 Exhaust outlet
430; 430A; 430B, 740A; BB740A
872462
Exhaust pipe
872462 Exhaust pipe
430; 430A; 430B, 740A; BB740A
856912
 
856912 Exhaust outlet
430; 430A; 430B, 740A; BB740A
872461
 
872461 Exhaust grommet
430; 430A; 430B, 740A; BB740A
7745660_023
Back to top