20593356 Fan hub Volvo.Penta
TAD520VE; TAD720VE; TAD721VE
Fan
Price: query
Rating:
Compatible models:
TAD520VE; TAD720VE; TAD721VE
Volvo.Penta
Volvo Penta entire parts catalog list:
Information:
Start By: The exhaust manifolds do not have to be removed unless all the cylinder head assemblies are to be removed.a. remove exhaust manifoldb. remove the valve cover1. Drain the coolant from the cooling system.2. Shut off the fuel supply at the fuel tank. 3. Remove fuel lines (1) from the cylinder head assembly.4. Remove fuel manifold (5).5. Remove lines (2) from water manifold (3).6. Remove water manifold (3). Air inlet elbow (4) does not have to be removed from the cylinder head assembly, only the bolts that hold the elbow to the cylinder head assembly.7. Remove the bolts from air inlet manifold (4). 8. Remove rocker shaft assembly (6) and push rods (7).9. Disconnect wire (8). 10. Disconnect the wire to fuel injector (9). Remove the clamp holding injector (9).11. Use a pry bar to raise fuel injector (9). Remove fuel injector (9) from the cylinder head.12. Remove the bolts and valve cover base (10). Remove the gasket and O-ring seals from beneath valve cover base (10). 13. Remove bridge assemblies (11).14. Fasten tooling (B) to the cylinder head using the threaded holes for the valve cover base. Support the cylinder head with a hoist.15. Remove eight bolts (12) and two bolts (13) to remove the cylinder head from the engine block. The weight of the cylinder head assembly is 47 kg (105 lb.). 16. Remove head gasket (14), the seals, the spacer plate and spacer plate gasket from the engine. The following steps are for installing the cylinder heads. Thoroughly clean the spacer plate and bottom surface of the cylinder head assembly. A new spacer plate gasket must be installed when the cylinder head assembly is removed.17. Install head gasket (14), the spacer plate and spacer plate gasket. Refer to the topic "Install Spacer Plate" in this module for further information.
The plug at location (A) MUST be installed in the cylinder head for this engine.
18. Fasten a hoist to the cylinder head assembly. Position the cylinder head assembly onto the spacer plate. 19. Put 5P3931 Anti-Seize Compound on the threads of cylinder head bolts (12) and (13). Install the cylinder head bolts and washers. Tighten the bolts in the following sequence:a. Tighten bolts (12) in the numbered sequence to a torque of 30 5 N m (22 4 lb. ft.).b. Tighten bolts (12) in the numbered sequence to a torque of 400 35 N m (300 26 lb. ft.).c. Tighten bolts (12) in the numbered sequence to a torque of 575 20 N m (420 15 lb. ft.).d. Tighten bolts (13) to a torque of 55 10 N m (40 7 lb ft).20. Remove tooling (B).21. Make sure the O-ring seals are installed around the two dowels in the bottom of valve cover base (3). Put the gasket and base (3) in position. Install valve cover base (3) to the cylinder head.22. Reverse the procedures and steps 1 through 12. Make sure all surfaces are clean. Replace all gaskets. Lubricate the O-ring seals with clean engine oil when assembling. Refer to Testing & Adjusting for further information.End By:a. install the exhaust manifoldb. install the valve cover
The plug at location (A) MUST be installed in the cylinder head for this engine.
18. Fasten a hoist to the cylinder head assembly. Position the cylinder head assembly onto the spacer plate. 19. Put 5P3931 Anti-Seize Compound on the threads of cylinder head bolts (12) and (13). Install the cylinder head bolts and washers. Tighten the bolts in the following sequence:a. Tighten bolts (12) in the numbered sequence to a torque of 30 5 N m (22 4 lb. ft.).b. Tighten bolts (12) in the numbered sequence to a torque of 400 35 N m (300 26 lb. ft.).c. Tighten bolts (12) in the numbered sequence to a torque of 575 20 N m (420 15 lb. ft.).d. Tighten bolts (13) to a torque of 55 10 N m (40 7 lb ft).20. Remove tooling (B).21. Make sure the O-ring seals are installed around the two dowels in the bottom of valve cover base (3). Put the gasket and base (3) in position. Install valve cover base (3) to the cylinder head.22. Reverse the procedures and steps 1 through 12. Make sure all surfaces are clean. Replace all gaskets. Lubricate the O-ring seals with clean engine oil when assembling. Refer to Testing & Adjusting for further information.End By:a. install the exhaust manifoldb. install the valve cover
Parts fan Volvo Penta:
21109801
21109801 Fan console
D5A-T; D5A-TA; D5A-B TA, TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TD520GE; TAD530GE; TAD531GE
20459039
21160271
21160271 Fan console
TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TD520GE; TAD530GE; TAD531GE
20405968
20405968 Fan, hot climate
TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TD420VE; TAD420VE; TAD620VE, TD520GE; TAD530GE; TAD531GE
20412753
20412753 Fan, hot climate
TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TAD550GE; TAD551GE; TAD750GE, TAD650VE; TAD660VE, TAD750VE; TAD760VE, TD420VE; TAD420VE; TAD620VE, TD520GE; TAD530GE; TAD531GE
3827487
3827487 Fan, suction type
TAD520VE; TAD720VE; TAD721VE, TAD560VE; TAD561VE; TAD761VE, TAD650VE; TAD660VE, TAD750VE; TAD760VE, TD420VE; TAD420VE; TAD620VE, TD610V; TWD610V; TD630VE, TD71A; TID71A; TWD710V
20555183
20412427
20412427 Fan, pusher type
TAD520VE; TAD720VE; TAD721VE, TD420VE; TAD420VE; TAD620VE, TD520GE; TAD530GE; TAD531GE