21662803 Fan shroud Volvo.Penta
TAD550GE; TAD551GE; TAD750GE, TAD734GE
Fan
Price: query
Rating:
Compatible models:
TAD550GE; TAD551GE; TAD750GE
TAD734GE
Volvo.Penta
Volvo Penta entire parts catalog list:
- Cooling System » 21662803
Information:
1. Disconnect fuel lines (2) and (3) from the fuel transfer pump.2. Remove the bolts that hold the fuel transfer pump. Remove fuel transfer pump (1) from the governor fuel pump drive.3. Check the seal on the fuel transfer pump for damage. Check gasket on the governor fuel pump drive housing. Use the reverse procedure of Steps 1 through 3 for installation of the fuel transfer pump. Remove (bleed) the air from the fuel system. See the procedures in the Testing And Adjusting module.Disassemble Fuel Transfer Pump
START BY:a. remove fuel transfer pump 1. Remove tachometer drive (3) from transfer pump cover (4).2. Remove bolts (1). Make a separation between cover (4) and pump body (2). 3. Remove lip-type seal (6) from the cover. Remove plug (5), seal, spring and plunger (bypass valve) from the cover. 4. Remove nut (10) from shaft (7). Remove gear (9) and key (11).5. Remove shaft (7) and gear (8) as a unit. Remove gear (8) from drive shaft (7) with a press.6. Remove idler gear (12). 7. Remove bushing (14), two lip-type seals and the bottom bearing from pump body (2).8. Remove check valve (13).Assemble Fuel Transfer Pump
1. Install bushing (4) in body (3) with tooling (B). The bushing must be .8 .5 mm (.031 .020 in.) below the (gear) surface of the body.2. Install the check valve in the body with tooling (A).3. Install lip-type seal (5) with tooling (C). Install the seal until it is 26.19 .13 mm (1.031 .005 in.) from the bottom (drive gear) surface of body (3) and with the lip toward bushing (4) as shown.4. Install lip-type seal (6) with tooling (D). Install the seal until it is 14.2 0.5 mm (.559 .020 in.) from the bottom (drive gear) surface of body (3) and with the lip away from seal (5) as shown.5. Install bearing (7) in body (3) with tooling (E). The bearing must be even with the bottom (drive gear) surface of the pump body. 6. Heat gear (8) to a maximum temperature of 316°C (600°F). Install gear (8) on shaft (11) until dimension (X) is 49.71 0.25 mm (1.957 .010 in.).7. Install the drive shaft and gear in body (3). Install key, gear (10) and nut (9). Tighten the nut to a torque of 30 7 N m (22 5 lb.ft.).8. Install idler gear (12) in body (3).9. Install lip-type seal (2) with tooling (C). Install the seal until it is 22.61 .05 mm (.890 .002 in.) from the top surface of cover (1) with the lip toward the inside as shown. 10. Install plunger (14) (bypass valve), spring (15), seal and plug (13) in pump cover (1). Tighten plug (13) to a torque of 37 4 N m (27 3 lb.ft.).11. Put 7M7260 Liquid Gasket Material on the surface of cover (1). Install cover (1) on pump body (3).
Do not let the liquid gasket enter the pump.
The drive shaft must turn freely after the bolts that hold the transfer pump together are tightened.12. Install the tachometer drive on cover (1).END BY:a. install fuel transfer pump
START BY:a. remove fuel transfer pump 1. Remove tachometer drive (3) from transfer pump cover (4).2. Remove bolts (1). Make a separation between cover (4) and pump body (2). 3. Remove lip-type seal (6) from the cover. Remove plug (5), seal, spring and plunger (bypass valve) from the cover. 4. Remove nut (10) from shaft (7). Remove gear (9) and key (11).5. Remove shaft (7) and gear (8) as a unit. Remove gear (8) from drive shaft (7) with a press.6. Remove idler gear (12). 7. Remove bushing (14), two lip-type seals and the bottom bearing from pump body (2).8. Remove check valve (13).Assemble Fuel Transfer Pump
1. Install bushing (4) in body (3) with tooling (B). The bushing must be .8 .5 mm (.031 .020 in.) below the (gear) surface of the body.2. Install the check valve in the body with tooling (A).3. Install lip-type seal (5) with tooling (C). Install the seal until it is 26.19 .13 mm (1.031 .005 in.) from the bottom (drive gear) surface of body (3) and with the lip toward bushing (4) as shown.4. Install lip-type seal (6) with tooling (D). Install the seal until it is 14.2 0.5 mm (.559 .020 in.) from the bottom (drive gear) surface of body (3) and with the lip away from seal (5) as shown.5. Install bearing (7) in body (3) with tooling (E). The bearing must be even with the bottom (drive gear) surface of the pump body. 6. Heat gear (8) to a maximum temperature of 316°C (600°F). Install gear (8) on shaft (11) until dimension (X) is 49.71 0.25 mm (1.957 .010 in.).7. Install the drive shaft and gear in body (3). Install key, gear (10) and nut (9). Tighten the nut to a torque of 30 7 N m (22 5 lb.ft.).8. Install idler gear (12) in body (3).9. Install lip-type seal (2) with tooling (C). Install the seal until it is 22.61 .05 mm (.890 .002 in.) from the top surface of cover (1) with the lip toward the inside as shown. 10. Install plunger (14) (bypass valve), spring (15), seal and plug (13) in pump cover (1). Tighten plug (13) to a torque of 37 4 N m (27 3 lb.ft.).11. Put 7M7260 Liquid Gasket Material on the surface of cover (1). Install cover (1) on pump body (3).
Do not let the liquid gasket enter the pump.
The drive shaft must turn freely after the bolts that hold the transfer pump together are tightened.12. Install the tachometer drive on cover (1).END BY:a. install fuel transfer pump
Parts fan Volvo Penta:
20412753
20412753 Fan, hot climate
TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TAD550GE; TAD551GE; TAD750GE, TAD650VE; TAD660VE, TAD750VE; TAD760VE, TD420VE; TAD420VE; TAD620VE, TD520GE; TAD530GE; TAD531GE
20412484
20412484 Fan
TAD520GE; TAD720GE; TAD721GE, TAD550GE; TAD551GE; TAD750GE, TD520GE; TAD530GE; TAD531GE, TD520VE; TD720VE
20798740
21205930
21632721
21034351
21757559
21072174