7745750_061 Volvo.Penta Fan hub

Table 1
Diagnostic Trouble Codes for High Coolant Temperature
J1939 Code Code Description Comments
110-0 Engine Coolant Temperature : High - most severe The Electronic Control Module (ECM) detects the following conditions:
The coolant temperature is greater than 110° C (230° F) for 10 seconds.
The ECM has been powered for at least 2 seconds.
There are no electrical faults or battery faults on the circuit.
The warning lamp will come on. The engine will be derated.
110–15 Engine Coolant Temperature : High - least severe (1) Probable Causes
Diagnostic codes
Coolant level
Coolant temperature sensor
Radiator and hoses
Radiator cap and pressure relief valve
Water temperature regulator
Engine cooling fan
Quality of coolant
Coolant pump
NRS cooler
Cylinder head gasketRecommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 2
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Turn the keyswitch to the ON position.
B. Establish communication between the electronic service tool and the ECM. Refer to Troubleshooting, Electronic Service Tools, if necessary.
C. Download the Product Status Report (PSR) with histograms before performing any troubleshooting or clearing any diagnostic codes.
Note: The downloaded information will be required by the Dealer Solutions Network (DSN) if troubleshooting assistance is required.
D. Use the electronic service tool to check for active or logged codes.
Diagnostic Codes
Result: One of the following diagnostic codes is active or logged:
• 1077–2
•1077–8
•2840–12
•2840–14
•3509–4
•3510–4
•168–4
•110–3
•110–4
Return the unit to service.
Repair: Refer to TroubleshootingDiagnostic Trouble Codes to troubleshoot the code.
Result: A 110-0 or 110–15 diagnostic code is present.
Proceed to Test Step 2.
2. Inspect Electrical Connectors and Wiring
A. Turn the keyswitch to the OFF position.
B. Inspect the connector for the coolant temperature sensor. Refer to Troubleshooting, Electrical Connectors - Inspect.
C. Perform a 45 N (10 lb) pull test on each of the wires in the suspect sensor connector and the sensor connections at the ECM.
D. Check the ground connection on the ECM for abrasions and pinch points.
E. Check the harness for abrasions and pinch points from the suspect sensor to the ECM.
Loose connection or damaged wire
Result: There is a fault in a connector or the wiring.
Repair: Repair any faulty connectors or replace the wiring harness. Ensure that all the seals are properly in place and ensure that the connectors are correctly coupled.
Result: All connectors, pins, and sockets are correctly coupled and/or inserted. The harness is free of corrosion, abrasion, and pinch points.
Proceed to Test Step 3.
3. Coolant Level
A. Check the coolant level.
Engine coolant level
Result: The engine coolant level is low.
Repair: Check the cooling system for leaks. Refer to Systems Operation, Testing, and Adjusting, "Cooling System - Inspect" for additional information. Repair any leaks immediately.
Result: The engine coolant level is OK.
Proceed to Test Step 4.
4. Condition of the Alternator Drive Belts
A. Inspect the condition of the belts.
B. Check the belt tension. If the engine is equipped with an automatic belt tensioner, check the automatic belt tensioner.
Drive belt
Result: The belts are in good condition and the belt tension is correct.
Proceed to Test Step 5.
Result: The belts are not in a good condition or the belt tension is incorrect.
Repair: If the belts are worn or damaged, replace the belts. Refer to Disassembly and Assembly for the correct procedure.
If necessary, replace the automatic belt tensioner. Refer to Disassembly and Assembly for the correct procedure.
Proceed to Test Step 5.
5. Coolant Temperature Sensor
A. Compare the reading for the coolant temperature on the electronic service tool to the reading for the coolant temperature on a calibrated test gauge.
Coolant temperature sensor
Result: The temperature sensor is not accurate.
Repair: Troubleshoot the circuit and the coolant temperature sensor. Refer to Troubleshooting, "Sensor Signal (Analog, Passive) - Test".
Result: The temperature sensor is reading accurately.
Proceed to Test Step 6.
6. Radiator and Hoses
A. Check the radiator fins for dirt, debris, and/or damage.
B. Check for collapsed hoses and/or other restrictions.
C. Check the radiator for internal blockage.
Ensure that the radiator size is sufficient. An undersized radiator does not have enough area for the effective release of heat. An undersized radiator may cause the engine to run at a temperature that is higher than normal. The normal temperature depends the ambient temperature.
Radiator and hoses
Result: The radiator fins are blocked or damaged.
Repair: Remove any dirt and/or debris and straighten any bent fins.
Result: The radiator has internal blockage.
Repair: Remove the blockage.
Result: The radiator fins are not damaged and the radiator does not have an internal blockage.
Proceed to Test Step 7.
7. Radiator Cap and Pressure Relief Valve
A. Pressure-test the cooling system. Refer to Systems Operation, Testing, and Adjusting, "Cooling System" for the correct procedure.
B. Check that the seating surfaces of the pressure relief valve and the radiator cap are clean and undamaged.
C. Check operation of the pressure relief valve and/or the water temperature regulator.
Radiator cap
Result: The pressure relief valve and/or the water temperature regulator are not operating correctly.
Repair: Clean the components or replace the components.
Result: The pressure relief valve and/or the water temperature regulator are operating correctly.
Proceed to Test Step 8.
8. Water Temperature Regulator
A. Check the water temperature regulator for correct operation. Refer to Systems Operation, Testing, and Adjusting, "Cooling System" for the proper procedure.
Water Temperature Regulator
Result: The water temperature regulator is not operating correctly.
Repair: Replace the water temperature regulator. Refer to Disassembly and Assembly, "Water Temperature Regulator - Remove and Install".
Result: The water temperature regulator is operating correctly.
Proceed to Test Step 9.
9. Engine Cooling Fan
A. Check that the cooling fan is operating correctly.
B. Check the engine cooling fan for damage.
Fan
Result: The cooling fan is not operating correctly.
Repair: Make sure that the cooling fan is being driven correctly. Make sure that the belt is correctly tensioned.
Result: The fan is damaged.
Repair: Repair the fan or replace the fan, as necessary. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Result: The fan is OK.
Proceed to Test Step 10.
10. Quality of Coolant
A. Check the quality of the coolant. Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations - Coolant".
Coolant
Result: The coolant is not of an acceptable quality.
Repair: Drain and refill the coolant system with coolant of the correct quality. Refer to the Operation and Maintenance Manual, "Refill Capacities and Recommendations - Coolant".
Result: The coolant is of an acceptable quality.
Proceed to Test Step 11.
11. Inspection of the Coolant Pump
A. Inspect