20877939 Volvo.Penta Filter cap

Table 1
J1939 Code and Description CDL Code and Description Comments
625–9
Proprietary Data Link : Abnormal Update Rate N/A N/A
639-9
J1939 Network #1 : Abnormal Update Rate 247-9
SAE J1939 Data Link : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
639-14
J1939 Network #1 : Special Instruction 247-14
SAE J1939 Data Link : Special Instruction The affected ECM is missing expected parameters.
1231-9
J1939 Network #2 : Abnormal Update Rate 2348-9
SAE J1939 Data Link #2 : Abnormal Update Rate Communication has been lost to one or more of the devices on the datalink. If multiple devices are not communicating, there is likely a problem with the data link wiring, power, or ground circuits.
Note: This code will log on the aftertreatment ECM if the Emergency Fuel Cutoff (EFCO) switch is used to shutdown the engine.
1231-14
J1939 Network #2 : Special Instruction 2348-14
SAE J1939 Data Link #2 : Special Instruction The affected ECM is missing expected parameters.
4193-9
Engine Coolant Pump Outlet Temperature : Abnormal Update Rate 2854-7
Coolant Temperature Control Module : Not Responding Properly N/A
4193-14
Engine Coolant Pump Outlet Temperature : Special Instruction 2349-14
Engine Coolant Pump Outlet Temperature Sensor : Special Instruction N/A
Table 2
Cat® ET Diagnostic Code Cross Reference to Wiring Schematic
Code Description Data Link
J1939 Network #1 Can A (Global)
J1939 Network #2 Can B (Local) Refer to the main engine Schematic, UENR7142 when troubleshooting the Data Link-Test.-9 Detected Problems:Device 1 is unable to communicate on the data link.
Device 1 cannot communicate with other Devices on the data link, but can communicate with the service tool, indicating a problem with the data link wiring.Device 1 is unable to communicate with Device 2 on the data link.
Device 1 cannot communicate with Device 2, indicating a problem with the data link wiring, power or ground circuit, or Device 2.-14 Detected Problems:Device 1 is unable to obtain a network address on the data link.
Device 1 is trying to claim the same address as another Device. An example of this is two Devices being configured the same.Device 1 detects a failed address claim from Device 2 on the data link.
Device 1 detects that Device 2 is trying to claim the same address as another Device.Device 1 is not receiving all expected parameters from Device 2 on the data link.
A component is configured as installed in the ECM, but is not installed on the application.
The incorrect component is installed.
The incorrect software file has been installed.
Illustration 1 g06320023
Table 3
Troubleshooting Test Steps Values Results
1. Check for Codes
A. Connect Cat® Electronic Technician (ET) to the service tool connector.
B. Look for active codes that are associated with the system for the diagnostic code.
Codes
Result: A 4193-9 code is present.
Proceed to Test Step 11.
Result: A 4193-14 is present code.
Proceed to Test Step 3.
Result: A 639-9, 1235-9 639-9, 639-14 are present.
Proceed to Test Step 2.
2. Use the "System Communication Status" to Determine the Communication Issue
A. In Cat ET, click on the "Diagnostics" tab on the tool bar.
B. Select the "System Communication Status" option from the drop-down list.
Component Identified Result: A 625-9 code is present.
Check the configuration of the secondary ECM to make sure that it is configured for the correct location.
The secondary ECM is Device 2.
Proceed to Test Step 7.
Result: A -9 code is active. Refer to the above -9 detected problems for additional information.
Proceed to Test Step 6.
Result: A -14 code is active. Refer to the above -14 detected problems for additional information.
If the NOx sensors are listed as ECM 2, proceed to Test Step 3.
For all other components, proceed to Test Step 4.
3. Check the Part Number of the Component
A. Locate the part number for the component that was identified by the "System Communication Status". Check to see if the part number is correct for the application.
Part Number
Result: The part number is incorrect for the application.
Repair: Replace the component with the correct part number. Refer to Special Instruction, REHS8151 for special handling instructions if replacing a NOx sensor.
Proceed to Test Step 10.
Result: The part number is correct for the application.
Proceed to Test Step 4.
4. Check for Incorrect Configuration Parameters
A. Connect Cat ET.
B. Use Cat ET to verify that the correct parameters are being used.
Parameters
Result: The parameters are correct.
Proceed to Test Step 5.
Result: The parameters are not correct.
Repair: Input the correct parameters. Refer to Troubleshooting, "Configuration Parameters" for additional information.
If the problem is not resolved, proceed to Test Step 5.
5. Ensure that the latest Flash File Software is Installed in the ECM
A. Connect Cat ET.
B. Use Cat ET to verify that the correct flash file is being used.
Flash File
Result: The latest flash file is installed and the code present was 4193-14.
Proceed to Test Step 13.
Result: The latest flash file is installed and the code present was not 4193-14.
Proceed to Test Step 10.
Result: The latest flash file is not installed.
Repair: Perform the following procedure:
1. Download the latest flash file from SIS Web.
2. Install the software into the ECM.
Refer to Troubleshooting, "ECM Software - Install" for additional information.
Proceed to Test Step 10.
Illustration 2 g03846524
Device 1 present
(1) Column 1
Illustration 3 g03846007
Device 1 and Device 2 present
(1) Column 1
(2) Multiple Device 1 and Device 2 can be displayed
(3) Device 2 is the affected ECM/device that cannot be recognized by Device 1. Device 2 i