6613372 Volvo.Penta Fitting


6613372 Fitting Volvo.Penta MD22A; MD22A-A; MD22L-A, MD22L; MD22P; MD22L-B Fitting
6613372 Fitting Volvo Penta
Rating:
18

Buy Fitting 6613372 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 16
 

Compatible models:

Volvo Penta entire parts catalog list:

MD22A; MD22A-A; MD22L-A; TMD22A; TMD22-A; MS2B-A; MS2B-R; MS2A-E; MS2B-L; MS2L-E; 120S-E; MD22; MD22L
MD22L; MD22P; MD22L-B; MD22P-B; TMD22-B; TMD22P-C; TAMD22P-B; HS25A; HS25A-B; 120S-E; MS2A-E; MS2L-E; MS2B-L; TMD22B

Information:


Table 1
Diagnostic Trouble Code
J1939 Code Code Description
(code descriptions may vary) Comments
174-15 Engine Fuel Temperature 1 : High - least severe (1) The fuel temperature is above an acceptable level.
If equipped, the action lamp will illuminate.
The code is logged.
174-16 Engine Fuel Temperature 1 : High - moderate severity (2) The fuel temperature is above an acceptable level.
If equipped, the action lamp will illuminate.
The code is logged.
There may be a decrease in power.
174-0 Engine Fuel Temperature 1 : High - most severe (3)
Table 2
Associated Codes
Suspect Parameter Number (SPN)
5580-17
5580-18
Table 3
Troubleshooting Test Steps Values Results
1. Determine the Code
A. Check for active codes and check for logged codes on Caterpillar Electronic Technician (ET).
B. Check Cat ET for any associated codes that are listed in Table 2. Troubleshoot any active codes before continuing with this procedure.
Diagnostic trouble code
Result: An associated code is active or logged.
Troubleshoot any active codes before continuing with this procedure.
Result: An associated code is not active or logged.
Proceed to Test Step 2.
2. Check the Fuel Level in the Fuel Tank
A. Check the fuel level in the fuel tank.
Fuel level
Result: The fuel level is acceptable.
Proceed to Test Step 3.
Result: The fuel level is not acceptable.
Fill the tank. Verify that the problem has been resolved. If the problem has not been resolved, proceed to Test Step 3.
Illustration 1 g02023433
Fuel supply lines
Illustration 2 g02024502
Fuel return line
Illustration 3 g02338176
Table 4
Troubleshooting Test Steps Values Results
3. Inspect the Fuel Supply Lines
A. Visually inspect the fuel lines between the priming pump and the inlet to the cylinder head. Also, inspect the fuel cooler for dirt, debris, or damage, if equipped. Inspect the fuel return line from the head to the fuel tank. Inspect the lines for restrictions, pinching, and swelling. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
B. Inspect the fuel cooler for dirt, debris, or damage, if equipped.
Dirt and debris or damage
Result: The fuel lines and the cooler (if equipped) are OK.
Proceed to Test Step 4.
Result: The fuel lines and the cooler (if equipped) are not OK.
Replace damaged fuel lines and/or fuel cooler (if equipped). Remove dirt or debris from fuel cooler fins (if equipped). Verify that the problem has been resolved.
If the problem is not resolved, proceed to Test Step 4.
4. Replace the Temperature Sensor
A. Replace the fuel temperature sensor.
B. Check for active codes or logged codes.
Active codes or logged codes
Result: A 174 code is active or logged.
Proceed to Test Step 5.
Result: A 174 code is not active or logged.
Return the unit to service.
Illustration 4 g02024574
(1) Fuel return pressure regulator
Table 5
Troubleshooting Test Steps Values Results
5. Fuel Return Pressure Regulator
A. Replace the fuel return pressure regulator.
Pressure regulator
Result: The problem has been resolved.
Return the unit to service.
Result: The problem has not been resolved.
Proceed to Test Step 6.
6. Perform a Cylinder Cutout Test
A. Perform a "Cylinder Cutout Test" in Cat ET.
Test was not successful
Result: The Cylinder Cutout Test was not successful.
Replace the identified injectors. Verify that all trim files are installed into the ECM correctly. Refer to Troubleshooting, "Injector Trim File - Install". Repeat the "Fuel System Verification Test" after making the necessary repairs. Repeat the process until all the injectors are operating properly.
Complete the procedure in the order in which the steps are listed.


Parts fitting Volvo Penta:

954322
 
954322 Fitting nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B, AQ131A; AQ131B; AQ131C, AQ1
954323
 
954323 Fitting nut
2001; 2001B; 2001AG, 230A; 230B; 250A, 251A, 430; 430A; 430B, 500; 500A; 501A, 571A, 740A; BB740A, AD30A; AQAD30A; MD30A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AD41D; D41D; TAMD41D, AQ115A; AQ115B; AQ130, AQ120B; AQ125A; AQ140A, AQ125B,
483467
Fitting nut
483467 Fitting nut
MD22A; MD22A-A; MD22L-A, MD22L; MD22P; MD22L-B
954363
 
954363 Fitting
D100A; D100AK; D100B, D42A; D42A PP, MD22A; MD22A-A; MD22L-A, MD22L; MD22P; MD22L-B, TD30A; TD31ACE; TD40A
6634735
 
6634735 Fitting
MD22A; MD22A-A; MD22L-A, MD22L; MD22P; MD22L-B
954355
 
954355 Fitting nut
D100A; D100AK; D100B, D42A; D42A PP, MD22A; MD22A-A; MD22L-A, MD22L; MD22P; MD22L-B, TD30A; TD31ACE; TD40A
3853993
 
3853993 Fitting
MD22L; MD22P; MD22L-B, SX-C; SX-C1; SX-C2, TSKs; SX-M; 1998-2005
3853994
 
3853994 Fitting
MD22L; MD22P; MD22L-B, SX-C; SX-C1; SX-C2, SX-S; SX-SLT; SX-ST, TSKs; SX-M; 1998-2005
Back to top