21665182 Volvo.Penta Flange


21665182 Flange Volvo.Penta TAD560VE; TAD561VE; TAD761VE Flange
21665182 Flange Volvo Penta
Rating:
53

Buy Flange 21665182 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD560VE; TAD561VE; TAD761VE; TAD762VE; TAD763VE; TAD764VE; TAD765VE

Information:

1. Remove bolts that hold elbow (1) in position on the oil pump. Remove the lock and bolt (2) that holds the suction bell to the oil pan plate. 2. Bend the locks back and remove four bolts (3). Remove oil pump (4).
The oil pump idler gear will fall off the pump.
Install Oil Pump
1. Install the idler gear on the oil pump. Put the oil pump in position on the cylinder block and install locks and bolts (3). Be sure the idler gear is engaged with the crankshaft gear before bolts (3) are tightened. 2. Install the lock and bolt (2) that holds the suction bell to the oil pan plate.End By:a. install oil panDisassemble Oil Pump
Start By:a. remove oil pump 1. Remove idler gear (2). Remove the bearing from the idler gear with tooling (B).2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), the keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (B).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (B) and a press as follows:a. Put bearings (9) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is 1.52 mm (.060 in.) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (B) and a press as follows.a. Put bearings (10) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See the topic, Oil Pump in the Specifications module.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (11) cover (12) and bolt (5) in the oil pump body assembly. 6. Install shaft assemblies (13) in the oil pump body assembly.7. Install spacer (4). Install the key in the shaft assembly.8. Install the two gears on the shaft assemblies. 9. Install scavenge pump body assembly (14) and the bolts that hold it.10. Install key (15), drive gear (16), the washer and bolt (17). Tighten the bolt to a torque of 43 7 N m (32 5 lb.ft.).11. Install the bearing in the idler gear with tooling (B) and a press until it is even with the outside surface of the gear.12. Install the suction bell on the oil pump. Install the idler gear on the oil pump.
The oil pump must turn freely by hand after it is assembled.
End By:a. install oil pump


Parts flange Volvo Penta:

965215
 
965215 Flange screw
2001; 2001B; 2001AG, 430; 430A; 430B, 500; 500A; 501A, 740A; BB740A, AD31D; AD31D-A; AD31XD, AD31L-A; AD31P-A; AD41L-A, AQ225D; AQ225E; AQ225F, AQ260A; AQ260B; BB260A, BB231A; BB261A, D1-13; D1-13B; D1-20, D2-55; D2-55B; D2-55C, D2-75; D2-75B; D2-75C
990940
Flange nut
990940 Flange nut
1372, D1-13; D1-13B; D1-20, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D12D-A MG; D12D-E MG, D12D-A MH; D12D-B MH; D12D-C MH, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D1
984736
Flange screw
984736 Flange screw
1372, D11A-A; D11A-B; D11A-C, D11B1-A MP; D11B2-A MP, D11B3-A MP; D11B4-A MP, D13B-A MP; D13B-B MP; D13B-C MP, D13B-E MH; D13B-E MH (FE); D13B-N MH, D13B-F MG; D13B-E MG; D13B-E MG (FE), D13C1-A MP; D13C2-A MP; D13C3-A MP, D16C-A MG, D16C-A MH; D16C-
984759
 
984759 Flange screw
D11A-A; D11A-B; D11A-C, D13B-F MG; D13B-E MG; D13B-E MG (FE), D5A-T; D5A-TA; D5A-B TA, D5A-T; D5A-TA; D5A-B TA, D9A2A; D9A2A D9-425; D9A2A D9-500, D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1340VE; TAD1341VE; TAD1342VE, TAD1341GE; TAD1342GE; TAD1343GE, TAD135
11700326
 
11700326 Flange screw
D5A-T; D5A-TA; D5A-B TA, D5A-T; D5A-TA; D5A-B TA, TAD520GE; TAD720GE; TAD721GE, TAD520VE; TAD720VE; TAD721VE, TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE, TAD750VE; TAD760VE, TD520GE; TAD530GE; TAD531GE, TD520VE; TD720VE
975104
 
975104 Flange screw
8.1Gi-A; 8.1Gi-B; 8.1Gi-BF, D5A-T; D5A-TA; D5A-B TA, D5A-T; D5A-TA; D5A-B TA, TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE
20738626
 
20738626 Flange screw
TAD1340VE; TAD1341VE; TAD1342VE, TAD1360VE, TAD1361VE, TAD1363VE, TAD1640GE; TAD1641GE; TAD1642GE, TAD1641VE; TAD1642VE; TAD1643VE, TAD560VE; TAD561VE; TAD761VE
993447
 
993447 Flange screw
TAD550GE; TAD551GE; TAD750GE, TAD560VE; TAD561VE; TAD761VE, TAD734GE
Back to top