21648588 Volvo.Penta Flywheel housing


21648588 Flywheel housing Volvo.Penta TAD940VE; TAD941VE; TAD942VE Flywheel
21648588 Flywheel housing Volvo Penta
Rating:
63

Buy Flywheel housing 21648588 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

Volvo Penta entire parts catalog list:

TAD940VE; TAD941VE; TAD942VE; TAD943VE; TAD950VE; TAD951VE; TAD952VE

Information:


Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledgeMechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1. The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height adjustment tool (3).MEUI A Injector Adjustment
Table 1
Required Tools
Part Number Part Name Quantity
9U-7227 Injector Height Gauge 1
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height GaugeTo adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Injector height gauge (4) is used to obtain a dimension of 78.0 0.2 mm (3.07 0.01 inch). The dimension is measured from the top of the unit injector to the machined ledge of the fuel injector body.
Set the injector height tool body on top of the injector tappet body. The rod of the height adjustment tool should sit on the machined ledge of the injector body.
Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be flush with the injector height tool body.
Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 10 N m (74 7 lb ft).
To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360 degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on the exhaust stroke.
Repeat Steps 3 through 4.
Remove the timing bolt from the flywheel after all the unit injector adjustments have been made. Reinstall the valve mechanism cover.MEUI C Injector Overview
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connectorMechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3. The injectors typically have a raised tappet (1), and electrical connector (2).MEUI C Injector Adjustment
Set the engine to Top Dead Center (TDC) for number 1 piston. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Set injectors 3, 5, and 6 using the procedure that follows.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).
To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top of the injector.
Turn the adjustment screw an additional 180 degrees clockwise.
Hold the adjustment screw and torque the nut to 55 10 N m (41 7 lb ft).


Parts flywheel Volvo Penta:

3840861
 
3840861 Flywheel
D9A2A; D9A2A MG; D9A2A D9A-MG, TAD1140VE; TAD1141VE; TAD1142VE, TAD1150VE; TAD1151VE; TAD1152VE, TAD1170VE; TAD1171VE; TAD1172VE, TAD940VE; TAD941VE; TAD942VE
3589430
 
3589430 Flywheel
TAD940GE; TAD941GE, TAD940VE; TAD941VE; TAD942VE
3812547
 
3812547 Flywheel housing
TAD940VE; TAD941VE; TAD942VE
40005624
 
40005624 Flywheel housing
TAD940VE; TAD941VE; TAD942VE
3809405
 
3809405 Flywheel
TAD940VE; TAD941VE; TAD942VE
3838102
 
3838102 Flywheel
TAD940VE; TAD941VE; TAD942VE
3838100
 
3838100 Flywheel
TAD940VE; TAD941VE; TAD942VE
3838098
 
3838098 Flywheel
TAD940VE; TAD941VE; TAD942VE
Back to top