3818550 Volvo.Penta Flywheel housing


3818550 Flywheel housing Volvo.Penta D1-13; D1-13B; D1-20 Flywheel
3818550 Flywheel housing Volvo Penta
Rating:
78

Buy Flywheel housing 3818550 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 32
 

Compatible models:

D1-13; D1-13B; D1-20   Volvo.Penta

Volvo Penta entire parts catalog list:

D1-13; D1-13B; D1-20; D1-20B; D1-30; D1-30B; D2-40; D2-40B; D1-13F; D1-20F; D1-30F; D2-40F

Information:


Illustration 1 g01259598
Schematic for the 5 volt pressure sensor supply
Illustration 2 g01270567
Air cleaner assembly
(1) Turbocharger inlet pressure sensor
Illustration 3 g01270590
(2) J2/P2 ECM connector
(3) J1/P1 ECM connector Test Step 1. Inspect the Electrical Connectors and the Wiring
Remove electrical power from the ECM.
Illustration 4 g01270593
Left side engine view
(4) Turbocharger outlet pressure (No. 2)
(5) Intake manifold pressure sensor
(6) Atmospheric pressure sensor
(7) Fuel pressure sensor
(8) Engine oil pressure sensor
Thoroughly inspect connectors (2) and (3). Also, thoroughly inspect the connectors for each pressure sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 5 g01259697
P2 terminal locations
(P2-15) Intake manifold pressure
(P2-41) Turbocharger outlet pressure (No. 2)
(P2-17) Sensor return
(P2-28) Engine oil pressure
(P2-40) Fuel pressure
(P2-57) Atmospheric pressure
(P2-72) +5 V supply
Illustration 6 g01212799
P1 ECM connector
(P1-2) +5 V supply
(P1-3) Sensor return
(P1-15) Turbocharger inlet pressure
Illustration 7 g01159881
Sensor connector
(Terminal A) +5 V supply
(Terminal B) Sensor return
(Terminal C) Sensor signal
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the allen head screw of each ECM connector for the proper torque. Refer to Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the harness and wiring for abrasion and for pinch points from the pressure sensors back to the ECM. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The harness and connectors appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem with the connectors and/or wiring.Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled.Verify that the repair eliminates the problem.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore electrical power to the ECM.
Monitor the active diagnostic code screen on Cat ET. Check for an active 262-03 code and an active 262-04 code. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Remove electrical power from the ECM. Expected Result:No diagnostic codes are active.Results:
OK - No diagnostic codes are active.Repair: If any of the above codes are logged and the engine is not running properly, refer to Troubleshooting, "Troubleshooting Without a Diagnostic Code".If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - Either the 262-03 or 262-04 diagnostic code is active at this time. Proceed to Test Step 3.Test Step 3. Disconnect the Pressure Sensors and Check for Active Diagnostic Codes
Restore electrical power to the ECM.
Monitor the active diagnostic code screen on Cat ET while you disconnect each pressure sensor connector. Check for an active 262-03 code or an active 262-04 code. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Disconnect the following sensors one at a time:
Atmospheric pressure sensor
Intake manifold pressure sensor
Turbocharger outlet pressure sensor (No. 2)
Engine oil pressure sensor
Fuel pressure sensor
Auxiliary pressure sensorExpected Result:The diagnostic code deactivates when a particular sensor is disconnected.Results:
OK - The 262-03 or 262-04 diagnostic code deactivates when a particular sensor is disconnected.Repair: Connect the suspect sensor. If the code returns, replace the sensor. Connect all of the connectors. Verify that the problem is resolved.STOP
Not OK - The 262-03 or 262-04 diagnostic code remains active after all of the sensors are disconnected.


Parts flywheel Volvo Penta:

3840880
 
3840880 Flywheel
D1-13; D1-13B; D1-20
3809921
 
3809921 Flywheel
D1-13; D1-13B; D1-20
21140575
 
21140575 Flywheel housing
D1-13; D1-13B; D1-20
21729462
 
21729462 Flywheel housing
D1-13; D1-13B; D1-20
3840878
 
3840878 Flywheel
D1-13; D1-13B; D1-20
3840879
 
3840879 Flywheel
D1-13; D1-13B; D1-20
21193277
 
21193277 Flywheel
D1-13; D1-13B; D1-20
Back to top