22965380 Volvo.Penta Fuel hose

(1) Cover. Tighten the bolts evenly in small increases until the torque is ... 80 N m (60 lb ft)(2) Torque for bolts ... 36 N m (26 lb ft)(3) Torque for bolt ... 78 N m (55 lb ft)(4) Torque for bolt that holds piston ... 110 N m (80 lb ft)(5) Rotor clamp nut. Tighten nut until clearance between rear end plate and rotor is ... 0.03 to 0.08 mm (0.001 to 0.003 in)Check clearance again after the bolt for the clamp nut is tightened.(6) Torque for bolt that holds rotor ... 120 N m (90 lb ft)105-5080, 105-5081 Motor Group
(1) Tighten bolts in steps to a torque of ... 30 5 N m (22 4 lb ft)(2) Clearance between rotor and end plate ... 0.81 mm (.032 in)(3) Tighten bolts in steps to a torque of ... 11.3 N m (100 lb in)Pressure Regulating Valve For Air Starting Motor
Typical Example(1) Adjusting screw.(2) Inlet pressure ... 1725 kPa (250 psi) Maximum permissable inlet pressure ... 3100 kPa (450 psi)(3) Minimum outlet pressure ... 620 kPa (90 psi) Maximum outlet pressure ... 1030 kPa (110 psi)Electric
6V0890 (24V); 6V0927 (24V)
Rotation as viewed from drive end ... ClockwiseNo load conditions at 25°C (77°F): Speed ... 6950 1650 rpmCurrent draw ... 115 25AVoltage ... 23VClearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)(1) Torque for large terminal nuts ... 30.5 3.5 N m (270 30 lb in)(2) Torque for small terminal nuts ... 2.25 0.25 N m (20 2 lb in)(3) Torque for screws holding nose housing to lever housing ... 20.3 2.7 N m (15 2 lb ft) SolenoidCurrent consumption (draw) at 25°C (77°F): Pull in windings at 20V ... 49.3 3.3AHold in windings at 20V ... 6.8A maximum8C3644 (24V)
Rotation as viewed from drive end ... ClockwiseNo load conditions at 25°C (77°F): Speed ... 7643 1683 rpmCurrent draw ... 67.5 7.5AVoltage ... 23VClearance between pinion and housing (pinion clearance) ... 9.1 mm (.36 in)(1) Torque for large terminal nuts ... 30.5 3.5 N m (270 30 lb in)(2) Torque for small terminal nuts ... 2.25 0.25 N m (20 2 lb in)(3) Torque for motor frame terminal ... 8 3 N m (70 26 lb in) SolenoidCurrent consumption (draw) at 25°C (77°F): Pull in windings at 20V ... 56.5 4.5AHold in windings at 20V ... 14.6A7T0794 (24V)
Rotation as viewed from drive end ... ClockwiseNo load conditions at 25°C (77°F): Speed ... 5500 rpm minimumCurrent draw ... 140A maximumVoltage ... 24V(1) Torque for large terminal nuts ... 30.5 3.5 N m (270 30 lb in)(2) Torque for small terminal nuts ... 2.25 0.25 N m (20 2 lb in) SolenoidCurrent consumption (draw) at 25°C (77°F): Pull in windings at 24V ... 51AHold in windings at 24V ... 7A9X4452 (24V)
Rotation as viewed from drive end ... ClockwiseNo load conditions at 25°C (77°F): Speed ... 3300 rpm minimumCurrent draw ... 80A maximumVoltage ... 23.5V(1) Torque for 1/2 - 13 terminal nuts ... 30.5 3.5 N m (270 30 lb in)(2) Torque for 10 - 32 terminal nut ... 2.25 0.25 N m (20 2 lb in)(3) Torque for M10 × 1.5 terminal nut ... 17.5 2.5 N m (155 22 lb in)(4) Torque for bolt in end of terminal stud ... 1.5 0.5 N m (13 4 lb in) SolenoidCurrent consumption (draw) at 25°C (77°F): Pull in windings at 24V ... 103AHold in windings at 24V ... 19A