3825602 Volvo.Penta Fuel hose

Illustration 1 g02926916
OCP Control System Panel
(1) Display screen
(2) F4 Soft key
(3) F3 Soft key
(4) F2 Soft key
(5) F1 Soft key
(6) Control key
(7) AUX overview key
(8) Engine overview key
(9) Main menu
(10) Warning Indicator lamp (yellow)
(11) Alarm-acknowledge and silence key
(12) Shutdown Indicator lamp (red)
(13) Event reset key
(14) Event log key
(15) Run key
(16) Auto key
(17) Stop key
(18) Escape key
(19) Up key
(20) Right key
(21) OK key
(22) Down key
(23) Left key General Information
The main component of the Operator Control Panel (OCP) is the electronic control module (ECM). This section discusses the display, keys, and indicators on the control system panel of the ECM.
Sending start and stop signals to the engine
Providing visual and audible indications when warning or shutdown events occur
Displaying engine information
Displaying Suspect Parameter Number (SPN) and Failure Mode Identifier (FMI) information for events
Programming set points for the standard OCP (ECM configuration and monitoring system).OCP Front Panel Components
The following components can be found on the front panel of the OCP:
Information Display
Alarm Indicators
Alarm Acknowledge/Silence Key
Event Reset Key
Function Keys
Navigation Keys
System Overview KeysInformation Display
(1) Display Screen - Information from the ECM is displayed on the display screen. This screen is used for the following programming and display functions.
Displaying engine parameter information
Programming set points for the engine
Displaying engine event information
Programming the display preferences of the OCP
Changing password levels of the OCPAlarm Acknowledge/Silence Key
(10) Alarm Acknowledge/Silence Key - Pressing the alarm acknowledge/silence key will cause the horn relay output to turn off and silence the horn. Press the key (10) to cause any yellow or red flashing lights to turn off. Press the key (10) to cause flashing lights to become solid depending on the active status of the alarms. The alarm acknowledge/silence key may also be configured to send out a global alarm silence on the J1939 Data Link.Event Reset Key
(11) Event Reset Key - The event reset button will clear all inactive fault conditions.Alarm Indicators
Yellow Warning Light - The yellow warning light (10) is located directly above the alarm acknowledge/silence key (11). A flashing yellow light indicates that there is an unacknowledged active warning. A solid yellow light indicates that there are acknowledged warnings active. If there are any active warnings, the yellow light will change from flashing yellow to solid yellow after the alarm acknowledge/silence key is pressed. If there are no longer any active warnings, the yellow light will turn off after the alarm acknowledge/silence key is pressed.Red Shutdown Light - The red shutdown (12) light is located directly above the event reset key (13). A flashing red light indicates that there are unacknowledged active shutdown events. A solid red light indicates that there are acknowledged shutdown events active. If there are any active shutdown events, the red light will change from flashing red to solid red after the alarm acknowledge/silence key is pressed. Any condition that has caused a shutdown event must be manually reset. If there are no longer any active shutdown events, the red light will turn off.Function Keys
(2) F4 - Pressing the F4 key will enable the function that is described on the screen directly above this key. When this key is defined on screen to scroll up or down, the Scroll Up and Scroll Down keys will also function the same. (3) F3 - Pressing the F3 key will enable the function that is described on the screen directly above this key. When this key is defined on screen to scroll up or down, the Scroll Up and Scroll Down keys will also function the same. (4) F2 - Pressing the F2 key will enable the function that is described on the screen directly above this key. When this key is defined on screen to scroll up or down, the Scroll Up and Scroll Down keys will also function the same. (5) F1 - Pressing the F1 key will enable the function that is described on the screen directly above this key. When this key is defined on screen to scroll up or down, the Scroll Up and Scroll Down keys will also function the same. (15) RUN - Pressing the "RUN" key causes the OCP to enter the run mode as long as start and stop are not configured as hardwired inputs. If digital inputs are programmed to start/stop, then buttons will not function. Lights will still indicate engine state. (16) AUTO - Pressing the "AUTO" key causes the OCP to enter the auto mode as long as start and stop are not configured as hardwired inputs. If digital inputs are programmed to start/stop, then buttons will not function. Lights will still indicate engine state. (17) STOP - Pressing the "STOP" key causes the OCP to enter the stop mode or the cool down mode as long as start and stop are not configured as hardwired inputs. If digital inputs are programmed to start/stop, then buttons will not function. Lights will still indicate engine state. (18) Escape Key - The escape key is used during menu navigation in order to navigate up through the menu/submenu structure. Each key press causes the user to move backward (upward) through the menus. The escape key is also used in order to cancel data entry screens during set point programming. If the escape key is pressed during set point programming, then none of the changes displayed on the screen will be saved to memory. (21) OK Key - The OK key is used during menu navigation in order to move forward (downward) through the menu/submenu structure. The key is also used during set point programming in order to save set points changes. Pressing the OK key during set point programming causes set point changes to be saved to memory.Navigation Keys
(6) Control Key - The control key will navigate the display to the screen that allows the user to monitor and/or adjust the speed control of the engine. (9) Main Menu Key - The main menu will navigate the display to the main menu directly without having to navigate out of menus. (14) Event Log - The event log button will navigate the display