818433 Volvo.Penta Fuel hose


818433 Fuel hose Volvo.Penta AQ115A; AQ115B; AQ130, D42A; D42A PP Fuel
818433 Fuel hose Volvo Penta
Rating:
78

Buy Fuel hose 818433 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 21
 

Compatible models:

Volvo Penta entire parts catalog list:

AQ115A; AQ115B; AQ130; AQ130A; AQ130B; AQ130C; AQ130D; AQ165A; AQ170A; AQ170B; AQ170C; AQD21A; BB115A; BB115B; BB115C; BB165A; BB170A; BB170B; BB1
D42A; D42A PP

Information:

Start By:a. disassemble governorb. remove fuel injection pumps FLUID SPILLAGE CONTAINMENTCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to "TOOLS AND SHOP PRODUCT GUIDE, NENG2500", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose fluids according to local regulations and mandates. 1. Remove cover (1) and gasket from the fuel injection pump housing. 2. Remove rack (2) from the fuel injection pump housing.
If the original lifters are to be installed in the fuel injection pump housing, put identification marks on them as to their location in the housing.
3. Remove lifters (3) from the fuel injection pump housing. 4. Put the fuel injection pump housing on end on blocks, and use Tool (A) to remove snap ring (4) from the camshaft. 5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump housing to loosen washer (5) on the camshaft. Remove washer (5). 6. Remove camshaft (6) from the fuel injection pump housing. 7. Remove bearings (7) from the drive end of the fuel injection pump housing. 8. Remove bearings (8) from the governor end of the fuel injection pump housing.Assemble Fuel Injection Pump Housing
Be sure all oil passages are clear, and put clean oil on all parts before assembly. 1. Use Tooling (B) to install bearing (10) in the governor end of the fuel injection pump housing with junction (joint) (11) toward the top of the fuel injection pump housing. Install the bearing so it is 0.25 0.20 mm (.100 .008 in) below the surface of the housing.2. Use Tooling (B) to install bearing (9) in the governor end of the fuel injection pump housing so it is 7.16 0.13 mm (.282 .005 in) below the surface of the housing. 3. Use Tooling (B) to install bearing (12) in the drive end of the fuel injection pump housing with the junction (joint) in the bearing toward the top of the fuel injection pump housing. Install the bearing so it is 1.00 0.25 mm (9.039 .010 in) below the surface of the housing. 4. Install plate (13) of Tooling (C) on the drive end of the fuel injection pump housing to install the bearing for the rack. Use clean grease to hold the new rack bearing on driver (14) of Tooling (C). Install the driver and bearing in plate (13) with the groove in the driver in alignment with the pin in the plate and use a hammer to push the bearing into position. The bearing will be installed to the correct depth when the shoulder of the driver is against plate (13).5. Remove Tooling (C) from the fuel injection pump housing. The rack bearing must be installed so it is 0.25 0.25 mm (.010 .010 in) below the surface of the housing. 6. Install camshaft (6) in the fuel injection pump housing.7. Put the fuel injection pump housing on end, and put a block under the camshaft. 8. Put the washer (5) over the end of the camshaft and use Tooling (B) and a spacer (15) that has an inside diameter of 38.1 mm (1.50 in) and a length of 31.75 mm (1.250 in) to push the washer against its seat on the camshaft. Camshaft must have 0.285 0.235 mm (.0112 .0093 in) end play when washer is pushed against cam shoulder. 9. Use Tool (A) to install snap ring (4) in the groove in the camshaft. 10. Install six lifters (3) in the fuel injection pump housing with the groove in the lifter in alignment with the pin in the housing. 11. Install rack (2) in the fuel injection pump housing, with the groove in the end of the rack in alignment with the ear (tab) of the rack bearing, at the drive end of the fuel injection pump housing. The six lifters are all the same and can be mixed. 12. Install the gasket and cover (1) on the fuel injection pump housing.End By:a. assemble governorb. install fuel injection pumps


Parts fuel Volvo Penta:

829375
Fuel hose
829375 Fuel hose
AQ115A; AQ115B; AQ130, MD21B; AQD21B
831092
Fuel pump
831092 Fuel pump
AQ115A; AQ115B; AQ130
806364
Fuel pump
806364 Fuel pump
AQ115A; AQ115B; AQ130
824704
 
824704 Fuel hose
AQ115A; AQ115B; AQ130
831028
Fuel hose
831028 Fuel hose
AQ115A; AQ115B; AQ130
829079
 
829079 Fuel pipe
AQ115A; AQ115B; AQ130
829374
 
829374 Fuel pipe
AQ115A; AQ115B; AQ130
787103
 
787103 Fuel hose
D42A; D42A PP
Back to top