236594 Volvo.Penta Gasket

Illustration 1 g06138727
Schematic for the lubrication system
(1) Engine oil coolers
(2) Self-cleaning oil filter
(3) High-pressure fuel pump
(4) Low-pressure turbochargers
(5) Turbocharger mounting support
(6) Rear gear train
(7) Pressure relief valve for the lubrication system
(8) High-pressure turbochargers
(9) Engine block
(10) Engine oil cooler bypass valve
(11) Pressure regulator valve for the lubrication system
(12) Engine oil pump
(13) Suction screen
(14) Scavenge oil pump
(15) Engine oil pan
(16) Centrifugal oil filter
(17) Main oil galley
Illustration 2 g06143431
(17) Main oil galleryEngine oil pump (12) is a gear-type pump that generates flow for the lubrication system. The engine oil pump is mounted on the back side of the front gear housing. The pump gears are driven by a splined shaft connected to the front gear train. Oil is drawn into the inlet of the pump through a tube and through suction screen (13).The pressure regulator housing (11) is mounted to the engine oil pump. Within the regulator housing, a pressure regulator valve controls the engine oil pressure to 600 100 kPa (87 15 psi) at rated speed of the engine. In the case of a problem with the pressure regulator valve, pressure relief valve (7) limits the maximum pump outlet pressure to 850 kPa (123 psi). Both of the valves return excess engine oil to engine oil pan (10).Scavenge oil pump (14) transfers oil from the shallow end of the engine oil pan to the oil sump. The scavenge oil pump is driven by the front gear train.The pressurized oil is directed through engine oil coolers (1). The engine oil coolers lower the temperature of the engine oil before the engine oil is sent to the filters. If the oil coolers become restricted, engine oil cooler bypass valve (10) allows engine oil to bypass the oil coolers. If the pressure differential across the oil coolers exceeds 180 kPa (26 psi), the bypass valve will allow engine oil to bypass the oil coolers. The oil coolers are mounted to the left side of the engine.A supply line crosses the engine below the oil pan to supply oil to Self-Cleaning Oil Filter (SCF) (2) on the right side. The SCF cleans the engine oil.An oil line connected to the filter housing provides filtered oil to the high-pressure fuel pump (3). Return oil from the pump drains through the front cover and into the oil pan.Backflush oil from the self cleaning oil filter flows to the centrifugal oil filter (COF) (16). Return oil from the COF drains through the rear housing and into the oil pan.Clean engine oil from the SCF flows to the rear of the engine through a line into the cylinder block and main oil gallery (17). The main oil gallery is cast into engine block (8). The main oil gallery supplies oil to the camshaft bearings through drilled passages in the engine block. The engine oil flows around each camshaft journal to the camshaft follower and lifter assemblies. Engine oil flows from the main oil gallery to each cylinder head through extra drilled passages that provide oil to the rocker arms. There are also passages in the rocker arm supports that provide lubrication to the rocker arm shafts and valve guides.External oil lines connected to passages in the front and rear covers supply oil to the turbochargers (4). The return oil from the turbochargers drains back into the oil pan through mounting supports (5).The main oil gallery is connected to the main bearings by drilled holes. Drilled holes in the crankshaft connect the main bearing oil supply to the rod bearings. Oil flows to the connecting rod bushings and wrist pins through drilled passages in the connecting rods.
Illustration 3 g06143455
Piston cooling and lubrication of the piston pin
(18) Drilled passage
(19) Piston cooling jetsDrilled passage (18) that is in the connecting rod provides oil for the lubrication of the piston pin. Two piston cooling jets (19) are located below each piston. Each of the piston cooling jets direct a spray of engine oil toward the manifold that is behind the ring band of the piston. The manifold is used to direct heat away from the piston rings. The oil spray from the piston cooling jets is used to remove heat from the manifold.Engine oil is sent to the front gear group and rear gear group (6) through drilled passages. The drilled passages are in the front housing, the rear housing, and cylinder block faces. The passages are connected to the main oil gallery.
Illustration 4 g06138753
Right side view of engine
(20) Turbocharger engine oil supply line
(21) Oil drain holes in turbocharger support
(22) Engine oil supply line from engine blockEngine oil is supplied to high-pressure turbochargers from the rear of the block from behind cylinder number 19 (22). The oil line supply lines (20) split from the junction block to provide oil flow to both the low-pressure and high-pressure turbochargers. The return oil drains back into the rear housing through drains in the turbocharger support (21).