3852455 Volvo.Penta Gasket, manifold to engine


3852455 Gasket, manifold to engine Volvo.Penta 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE Gasket
3852455 Gasket, manifold to engine Volvo Penta
Rating:
73

Buy Gasket, manifold to engine 3852455 Volvo Penta genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$10.91
 

08-08-2019
100 Hundredths Pounds
Volvo Pent: Volvo Penta OMC Cobr
Volvo Penta OMC Cobra Stern Drive New OEM Exhaust Manifold Gasket, 3852455
SKU: 3852455 || Sold Each || Please verify your own fitment
$11.97
 

16-06-2023
0.2[0.09] Pounds
-: -
EXHAUST MANIFOLD GASKET | GLM Part Number: 33790; Sierra Part Number: 18-0183; Mercury Part Number: 27-73866; OMC Part Number: 3852455
GLM Part Number: 33790; Sierra Part Number: 18-0183; Mercury Part Number: 27-73866; OMC Part Number: 3852455
Number on catalog scheme: 30
 

Volvo Penta entire parts catalog list:

5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE; 5.0FIPHURCE; 5.0FIPHUSCE; 5.0FLPHUB; 5.0FLPHUC; 5.0FLPHUE; 5.0FLPHUR; 5.0FLPHUS; 5.8FIIHUBCE; 5.8FII
5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE; 5.0FIPNCSCE; 5.0FLPNCA; 5.0FLPNCB; 5.0FLPNCM; 5.0FLPNCS
5.0FLPMDA; 5.8FLPMDA
5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE; 5.8FIPNCSCE; 5.8FLINCC; 5.8FLINCS; 5.8FLPNCA; 5.8FLPNCB; 5.8FLPNCM; 5.8FLPNCS; 5.8FSIINCC; 5.8FSIINC

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 371-1079 Lift Plate 1
B 339-9352 Inj. Sys. Cap Kit 1
265-2256 Wipers 1
D 312-2840 Socket 1 Note: When Tooling (B) is removed, be careful to prevent contamination. Cleanliness is an important factor. Before assembly, clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected always.
Illustration 1 g02149623
Illustration 2 g06151585Note: Reuse dowel components after cleaning using clean solvent.
Do not use dowels that have been removed from the block. Use a dead blow hammer to install new dowel assembly in block. Install new dowel assembly by lightly tapping the dowel until the dowel assembly is flush with the block surface. Excessive force can damage the dowel or block. Refer to illustration 2. If only the top part of the dowel has been removed, Use a screwdriver to install the dowel and apply a torque of 2 N m (18 lb in).Remove the O-ring seals from dowel assembly (14). Clean and inspect the O-ring seals. If necessary, replace the O-ring seals with new O-ring seals. Remove Tooling (B) and clean oil supply hole. Install dowel assembly (14).Note: Important to replace fire ring with new fire ring.
Replace fire ring (15) with new fire ring (15). Install fire ring (15). Install a new gasket (13) onto the cylinder block.
Illustration 3 g06151438Note: Clean the bottom surface of the cylinder head and the top surface of the cylinder block.
Attach Tooling (A) and a suitable lifting device onto cylinder head (3). The weight of cylinder head (3) is approximately 68 kg (150 lb). Position cylinder head (3) onto the cylinder block.
Illustration 4 g06151461
Illustration 5 g06151463Note: Ensure that the sleeve is installed with the chamfer facing downward. The sleeve must be flush with the top of the cylinder head surface.
Install sleeves (16) in cylinder head (3). Sleeves (16) are installed in the two bolt holes as shown in illustration 4.
Illustration 6 g06151466
Illustration 7 g02161103
Lubricate the threads of bolts (4) with oil. Install bolts (4) and the washers. Hand tighten all bolts (4) in the numerical sequence to a maximum torque of 15 N m (11 lb ft). Use Tooling (D) to tighten bolts (4) in the numerical sequence to a torque of 100 10 N m (75 7 lb ft). Tighten bolts (4) again in the numerical sequence to a torque of 250 15 N m (185 11 lb ft). Tighten bolts (4) in the numerical sequence for an extra 180 5 degrees.
Install the unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Illustration 8 g02090762
Illustration 9 g01285695
Apply clean engine oil to area (X). Repeat for the opposite collar. Apply clean engine oil to the ends of tube assembly (6). Install tube assembly (6). Replace external O-ring seals on tube assembly (6) and lubricate the O-ring seals on the tube assembly with clean engine oil. Install tube assembly (6).Note: Do not allow the quill tube to contact any part of the engine while assembling.
Install new bolts (10) and new bolts (7) hand tight.
Evenly tighten new bolts (10) to a torque of 20 N m (15 lb ft) in increments no greater than 90 degrees. Evenly tighten new bolts (7) to a torque of 20 N m (15 lb ft) in increments no greater than 90 degrees.
Evenly tighten new bolts (10) to a torque of 40 N m (30 lb ft) in increments no greater than 45 degrees. Evenly tighten new bolts (7) to a torque of 40 N m (30 lb ft) in increments no greater than 45 degrees.
Connect harness assembly (9). Replace the O-ring seals on both ends of the tube assembly (5). Install tube assembly


Parts gasket Volvo Penta:

3855782
Gasket
3855782 Gasket
3.0GSMBYMCE; 3.0GSPBYCCE, 3.0GSMHUB; 3.0GSPHUB, 3.0GSMLKD; 3.0GSPLKD, 3.0GSMNCA; 3.0GSMNCS; 3.0GSPNCA, 3.0GSMWTR; 3.0GSMWTS; 3.0GSPWTR, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.
3852095
Gasket, fuel pump to engine
3852095 Gasket, fuel pump to engine
3.0GLMMDA; 3.0GSPMDA, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA, 5.0GL-F; 5.0GL-FF, 5.0GL-H; 5.0GL-HF, 5.0GLPBYC; 5.0GiPBYCCE; 5.7GSPBYC, 5.0GLPEFS; 5.0GiPEFS; 5.7GSPEFS, 5.0GLPWTR; 5.0GiPWTR;
3852637
 
3852637 Gasket
3.0GLMMDA; 3.0GSPMDA, 3.0GSMHUB; 3.0GSPHUB, 3.0GSMNCA; 3.0GSMNCS; 3.0GSPNCA, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.
3852111
Gasket
3852111 Gasket
4.3GL-A; 4.3GL-B; 4.3GL-C, 4.3GL-E; 4.3GL-EF, 4.3GL-G; 4.3GL-GF, 4.3GL-J; 4.3GL-JF, 4.3GL-P, 4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4
3850496
Gasket, exhaust elbow to manifold
3850496 Gasket, exhaust elbow to manifold
4.3GLMMDA; 4.3GLPMDA; 4.3GSPMDA, 4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPEFS; 4.3GiPEFS, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 4.3GLPWTC; 4.3GLPWTR; 4.3GSPWTC, 4.3GXi-B; 4.3GXi-BF; 4.3OSi-
3853577
 
3853577 Gasket, float needle seat
4.3GLPBYC; 4.3GSPBYC; 4.3GIPBYCCE, 4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 4.3GLPWTC; 4.3GLPWTR; 4.3GSPWTC, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE
3853574
 
3853574 Gasket, cover
4.3GLPHUB; 4.3GSPHUB; 4.3GSPHUS, 4.3GLPLKD; 4.3GLPLKE; 4.3GSPLKD, 4.3GLPNCA; 4.3GLPNCB; 4.3GLPNCS, 5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.7GiPHUS, 5.7GLPLKA; 5.7GLPLKD; 5.7GLPL
3852818
Gasket, valve cover
3852818 Gasket, valve cover
5.0FIPHUBCE; 5.0FIPHUCCE; 5.0FIPHUECE, 5.0FiPMDA; 5.0FiPMDM; 5.8FiPMDA, 5.0FIPNCACE; 5.0FIPNCBCE; 5.0FIPNCMCE, 5.0FLPMDA; 5.8FLPMDA, 5.8FIPNCACE; 5.8FIPNCBCE; 5.8FIPNCMCE
Back to top