3862249 Gasket Volvo.Penta
DPH-A; TSK DPH-B; TSK DPH-A, DPH-D; DPR-D; DPH-D1
Gasket
Price: query
Rating:
Number on catalog scheme: 2
Compatible models:
DPH-A; TSK DPH-B; TSK DPH-A
DPH-D; DPR-D; DPH-D1
Volvo.Penta
Volvo Penta entire parts catalog list:
- Housing and Center Tube » 3862249
- Housing and Center Tube
- Housing and Center Tube
- Extension Kit 1''
Information:
An Application File Will Not Download (First Attempt)
Check the type of the communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
Verify that the computer and the terminal are set to the same communication settings.Expected Results: The computer and the terminal have different communication settings.OK - The computer and the terminal have different communication settings. Change the settings on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal have the same communication settings. Replace the Panelview terminal.An Application File Will Not Download (Subsequent Attempts)
Verify that the computer and the terminal are set to the same communication settings.Expected Results: The computer and the terminal have different communication settings.OK - The computer and the terminal have different communication settings. Change the settings on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal have the same communication settings. Replace the Panelview terminal.No Communications With an SLC Controller or a PLC Controller
Check the type of the communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
Verify that the terminal and the controller are set at the same baud rate.Expected Results: The terminal and the controller are not set at the same baud rate.OK - The terminal and the controller are not set at the same baud rate. Change the baud rate of either the terminal or the controller so that the baud rates are the same. STOP.Not OK - The terminal and the controller are set at the same baud rate. Go to step 3.
Check to see if the controller is in the run mode.Expected Results: The controller is not in the run mode.OK - The controller is not in the run mode. Place the controller in the run mode. STOP.Not OK - The controller is in the run mode. Go to step 4.
Verify the address of the node.Expected Results: The terminal node and the maximum node numbers are not set correctly.OK - The terminal node and the maximum node numbers are not set correctly. Reset the terminal node and the maximum node numbers so that the numbers are correct. STOPNot OK - The terminal node and the maximum node numbers are set correctly. Replace the Panelview terminal.No Communications With the PLC and the "COMM" LED is Active
Verify the address of the controller.Expected Results: The Panelview terminal is trying to communicate with a controller at a different address.OK - The Panelview terminal is trying to communicate with a controller at a different address. Change the address of the controller. STOP.Not OK - The Panelview terminal is not trying to communicate with a controller at a different address. Go to step 2.
Check the setting of the inhibit bit.Expected Results: The inhibit bit is set as the default on the "Channel Status" screen in the PLC.OK - The inhibit bit is set as the default on the "Channel Status" screen in the PLC. Change the inhibit bit to the correct setting. STOP.Not OK - The inhibit bit is set to the correct setting on the "Channel Status" screen in the PLC. Replace the Panelview terminal.No Communications With the Computer
Check the type of communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
The personal computer interface converter receives power from the DH-485 connection. Verify that the terminal is connected to an SLC, network, or a wallmount power supply.Expected Results: The terminal is not connected to an SLC, network, or wallmount power supply.OK - The terminal is not connected to an SLC, network, or wallmount power supply. Connect the terminal to an SLC, network, or wallmount power supply.Not OK - The terminal is connected to an SLC, network, or wallmount power supply. Go to step 3.
Verify that the computer and the terminal are set to the same baud rate.Expected Results: The computer and the terminal have different baud rates.OK - The computer and the terminal are set to different baud rates. Change the baud rate on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal are set to the same baud rates. Go to step 4.
Verify the address of the node.Expected Results: The terminal node and the maximum node numbers are not set correctly.OK - The terminal node and the maximum node numbers are not set correctly. Reset the terminal node and the maximum node numbers so that the numbers are correct. STOPNot OK - The terminal node and the maximum node numbers are set correctly. Replace the Panelview terminal.
Check to see if there is a computer fault.Expected Results: There is a computer fault.OK - There is a computer fault. Refer to the user manual for the computer.Not OK - There is not a computer fault. Replace the Panelview terminal.
Check the type of the communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
Verify that the computer and the terminal are set to the same communication settings.Expected Results: The computer and the terminal have different communication settings.OK - The computer and the terminal have different communication settings. Change the settings on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal have the same communication settings. Replace the Panelview terminal.An Application File Will Not Download (Subsequent Attempts)
Verify that the computer and the terminal are set to the same communication settings.Expected Results: The computer and the terminal have different communication settings.OK - The computer and the terminal have different communication settings. Change the settings on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal have the same communication settings. Replace the Panelview terminal.No Communications With an SLC Controller or a PLC Controller
Check the type of the communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
Verify that the terminal and the controller are set at the same baud rate.Expected Results: The terminal and the controller are not set at the same baud rate.OK - The terminal and the controller are not set at the same baud rate. Change the baud rate of either the terminal or the controller so that the baud rates are the same. STOP.Not OK - The terminal and the controller are set at the same baud rate. Go to step 3.
Check to see if the controller is in the run mode.Expected Results: The controller is not in the run mode.OK - The controller is not in the run mode. Place the controller in the run mode. STOP.Not OK - The controller is in the run mode. Go to step 4.
Verify the address of the node.Expected Results: The terminal node and the maximum node numbers are not set correctly.OK - The terminal node and the maximum node numbers are not set correctly. Reset the terminal node and the maximum node numbers so that the numbers are correct. STOPNot OK - The terminal node and the maximum node numbers are set correctly. Replace the Panelview terminal.No Communications With the PLC and the "COMM" LED is Active
Verify the address of the controller.Expected Results: The Panelview terminal is trying to communicate with a controller at a different address.OK - The Panelview terminal is trying to communicate with a controller at a different address. Change the address of the controller. STOP.Not OK - The Panelview terminal is not trying to communicate with a controller at a different address. Go to step 2.
Check the setting of the inhibit bit.Expected Results: The inhibit bit is set as the default on the "Channel Status" screen in the PLC.OK - The inhibit bit is set as the default on the "Channel Status" screen in the PLC. Change the inhibit bit to the correct setting. STOP.Not OK - The inhibit bit is set to the correct setting on the "Channel Status" screen in the PLC. Replace the Panelview terminal.No Communications With the Computer
Check the type of communication cable and the connections.Expected Results: The communication cable is disconnected.OK - The communication cable is disconnected. Make sure the cable is the correct cable and connect the cable. STOP.Not OK - The communication cable is connected and the communication cable is the correct cable type. Go to step 2.
The personal computer interface converter receives power from the DH-485 connection. Verify that the terminal is connected to an SLC, network, or a wallmount power supply.Expected Results: The terminal is not connected to an SLC, network, or wallmount power supply.OK - The terminal is not connected to an SLC, network, or wallmount power supply. Connect the terminal to an SLC, network, or wallmount power supply.Not OK - The terminal is connected to an SLC, network, or wallmount power supply. Go to step 3.
Verify that the computer and the terminal are set to the same baud rate.Expected Results: The computer and the terminal have different baud rates.OK - The computer and the terminal are set to different baud rates. Change the baud rate on the computer or on the terminal so that the settings are the same for both. STOP.Not OK - The computer and the terminal are set to the same baud rates. Go to step 4.
Verify the address of the node.Expected Results: The terminal node and the maximum node numbers are not set correctly.OK - The terminal node and the maximum node numbers are not set correctly. Reset the terminal node and the maximum node numbers so that the numbers are correct. STOPNot OK - The terminal node and the maximum node numbers are set correctly. Replace the Panelview terminal.
Check to see if there is a computer fault.Expected Results: There is a computer fault.OK - There is a computer fault. Refer to the user manual for the computer.Not OK - There is not a computer fault. Replace the Panelview terminal.
Parts gasket Volvo Penta:
889455