842870 Volvo.Penta Gasket

Table 1
Diagnostic Codes Table
CDL Code Code Description Comments
168-2 Electrical System Voltage : Erratic, Intermittent, or Incorrect The engine is running. The battery voltage falls below 6 VDC and the voltage returns above 9 VDC for three voltage readings in the last 7 seconds.
168-3 Electrical System Voltage : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 Electrical System Voltage : Voltage Below Normal The ECM detects voltage that is below the acceptable value. The engine ECM requires the keyswitch to be in the ON position in order to maintain communications with Caterpillar Electronic Technician (ET).
Illustration 1 g02100347
Schematic for the electrical power supply circuit
Test Step 1. DETERMINE THE DIAGNOSTIC CODE
Establish communication between the Cat ET and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
Start the engine. Run the engine until the engine is at normal operating temperature.
Download the "Product Summary Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes. Look for these codes:
168-2
168-3
168-4Results:
A 168-2 diagnostic code is active. - Proceed to Test Step 2.
A 168-3 diagnostic code is active. - Proceed to Test Step 3.
A 168-4 diagnostic code is active. - Proceed to Test Step 4.Test Step 2. INSPECT THE ELECTRICAL CONNECTORS AND THE WIRING FOR THE CHARGING CIRCUIT
Turn the keyswitch to the OFF position.
Check the harness connections at the battery and at the alternator.
Check the harness between the battery and the alternator. Results:
OK - The harness and connectors appear to be OK.Repair: There is a problem with the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".STOP
Not OK - The connectors and/or wiring are not OK.Repair: Repair the wiring and/or the connectors. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are coupled. Verify that the repair eliminates the problem.STOPTest Step 3. CHECK THE CHARGING CIRCUIT
Check the operation of the charging circuit. Results:
Not OK - The battery voltage is high.Repair: There is a problem with the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".STOPTest Step 4. CHECK THE BATTERY
Turn the keyswitch to the ON position. Do not start the engine.
Check the brightness of the lights.
Turn the keyswitch to the ON position. Start the engine.
Check the brightness of the lights. Results:
OK - The lights are dim when the engine is not running. The lights are brighter when the engine is running. There is a problem with the battery. Proceed to Test Step 5.
Not OK - The lights are dim when the engine is not running. The lights are still dim when the engine is running.Repair: There is a problem with the charging system. Refer to Special Instruction, REHS0354, "Charging System Troubleshooting".STOPTest Step 5. CHECK THE BATTERY CHARGE
Measure the no-load battery voltage at the battery posts.
Test the batteries. Use the 4C-4911 Battery Load Tester. Refer to Special Instruction, SEHS9249, "Use of 4C-4911 Battery Load Tester for 6, 8 V and 12 V Lead Acid Batteries" and Special Instruction, SEHS7633, "Battery Test Procedure". Results:
OK - The batteries pass the load test. The measured voltage is between 11.0 VDC and 13.5 VDC for a 12 V system and between 22.0 VDC and 27.0 VDC for a 24 V system.Repair: Check the wiring between the batteries and the ECM.Check the connectors between the batteries and the ECM for moisture and/or corrosion.Repair the wiring and/or the connectors.Verify that the repair eliminates the problem.STOP
Not OK - The battery voltage is low or the battery did not pass the load test.Repair: Recharge or replace the faulty batteries. Verify that the repair eliminates the problem.STOP