3586547 Volvo.Penta Gear set


3586547 Gear set Volvo.Penta 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR Gear
3586547 Gear set Volvo Penta
Rating:
103

Buy Gear set 3586547 Volvo Penta genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

Information:


Illustration 1 g00855101
Typical exampleTest Step 1. Check for Connector Damage.
Turn the circuit breaker CB-8 to the OFF position.
Thoroughly inspect the connectors J1/P1 and J2/P2 of the Electronic Control Module (ECM). Inspect all of the other connectors. Refer to the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the harness and the wiring for abrasion and pinch points.Expected Result:The connectors and wiring should be free of the following problems: damage, corrosion, abrasion and incorrect attachment.Results:
OK - The wiring and connectors are okay. Proceed to test step 2.
Not OK - The wiring and/or connectors need repair.Repair: Repair the connectors or wiring and/or replace the connectors and wiring. Stop.Test Step 2. Check for a Short Circuit and/or an Open Circuit.
Disconnect J26/P26.
Measure the resistance between P26-1 and P26-2 .Expected Result:The resistance should be between 110 to 200 Ohms.Results:
OK - The resistance is between 110 Ohms to 200 Ohms. Proceed to test step 3.
Not OK - The resistance is not between 110 to 200 Ohms. The sensor is internally shorted or open.Repair: Replace the sensor. Stop.Test Step 3. Check for a Short Circuit in the Wiring Harness.
Disconnect ECM connector J1/P1.
Measure the resistance between J26-1 and J26-2.
Measure the resistance between P26-1 and engine ground.
Measure the resistance between P26-2 and engine ground. Expected Result:The resistance should be greater than 20,000 Ohms for each measurement.Results:
OK - The resistance is greater than 20,000 Ohms for each measurement. Proceed to test step 4.
Not OK - The resistance is less than 20,000 Ohms indicating a short circuit.Repair: Repair the connectors or wiring and/or replace the connectors and wiring. Stop.Test Step 4. Check the Resistance through the Harness.
Use a suitable piece of wire and connect P26-1 to P26-2.
Measure the resistance between P1-18 and P1-12.Expected Result:The resistance should be less than 10 Ohms through the wires.Results:
OK - The resistance is less than 10 Ohms through the wires. Proceed to test step 5.
Not OK - The resistance is more than 10 Ohms through the wires. There is an open circuit in the harness or connectors.Repair: Repair the connectors and wiring and/or replace the connectors and wiring. Stop.Test Step 5. Check the Signal Voltage at the Sensor Connectors.
Reconnect sensor connector J26/P26.
Disconnect ECM connector J1/P1.
Remove wire F723-WH from pin 18 of ECM connector P1. Remove wire F724-BK from pin 12 of ECM connector P1.
Reconnect ECM connector J1/P1.
Turn the circuit breaker CB-8 to the ON position.
Start the engine.
Decelerate the engine to low idle.
Set a multimeter on the 20 VAC position.
Measure the voltage between F723-WH and F724-BK.
Stop the engine. Turn the circuit breaker CB-8 to the OFF position.
Reinstall all wiring to the original configuration.Expected Result:The signal voltage should be greater than 6.0 VAC.Results:
OK - A valid signal voltage appears at the ECM connector P1. Proceed to test step 6.
Not OK - There is a problem in the harness or the sensor.Repair: Recheck for shorts or opens in the harness. If the problem is not resolved, adjust the air gap to approximately 0.9 mm (0.04 inch) and repeat this test. Stop.Test Step 6. Check for "ACTIVE" Diagnostic Codes.
Turn the circuit breaker CB-8 to the OFF position.
Start the Caterpillar Electronic Technician (ET).
Turn the circuit breaker CB-8 to the OFF position.
Leave the main disconnect switch in the OFF position.
Check for "ACTIVE" diagnostic codes.Expected Result:The diagnostic code 261-13 should NOT be active.Results:
OK - The sensor is working properly.Repair: The problem may be intermittent. If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Inspecting Electrical Connectors". Stop.
Not OK - A valid signal voltage appears at P1. The ECM is not reading the voltage properly.Repair: Replace the ECM. Perform the diagnostic procedure Troubleshooting, "Replacing the ECM". Stop.


Parts gear Volvo Penta:

40005267
 
40005267 Gear changing unit, shift mechanism
120S-A; 120S-B; 120S-D, 130S-C; 130SR-C, 130S; 130S-B; 130SR-A, 150S-C; 150SR-C, 150S; 150S-B; 150SR
3582879
 
3582879 Gear
120S-A; 120S-B; 120S-D, 130S; 130S-B; 130SR-A
3589556
 
3589556 Gear housing
130S; 130S-B; 130SR-A
3589557
 
3589557 Gear housing
130S; 130S-B; 130SR-A
3593848
 
3593848 Gear selector contro
130S-C; 130SR-C, 130S; 130S-B; 130SR-A
3584492
 
3584492 Gear housing
130S; 130S-B; 130SR-A
3819860
 
3819860 Gear housing
130S; 130S-B; 130SR-A
22094796
 
22094796 Gear housing
150S-C; 150SR-C
Back to top